查询词典 clearance angle

The cutting edge inclination and the clearance angle is 0°and 3°.

而刃倾角和后角分别为0°和3°。

GSM, etc. have been designed by employing the "clearance angle" model.

寻呼、NMT、GSM等）都采用&透过角&模型来进行设计。

An analysis of the effect of tooth path and optimum clearance angle on tool life in the up milling and down milling processes is presented.

就铣削轨迹长度而论，在相同的切削情况下顺铣的轨迹较短，但其差量甚小，仅占全长百分之几。

Empire Molding Wheel: mainly used for clearance angle \ gully.

Empire成型砂轮：主要用於清角\切沟。

The clearance angle is provided such that the tool will not rub the machined surface thus spoiling the surface and increasing the cutting forces.

后角 的作用是不使刀具与已加工表面摩擦，以免损坏表面和增加切削力。

This paper analyses affecting factor on zero degree clearance angle woodworking saws cutting force decreasing and increasing in same cutting condition.

文章从理论方面分析了在相同的切削条件下影响零锯料角木工锯子的切削力减小或增加的因素及其作用程度，得出了零锯料角木工锯子的切削力小于非零度锯料角木工锯子这一结论。

The results show that cutting tools and cutting parameters had an important influence on the quality of the fiber in the planing process of metal fiber. The larger rake angle and appropriate clearance angle of tools favored to fabricate metal fiber. Back engagement influenced the forming process of metal fibers most greatly, feed rate and cutting speed varied little.

研究结果表明：在金属纤维刨削成形过程中，刀具参数和切削用量对纤维的质量有重要影响，较大的刀具前角和合适的刀具后角有利于纤维的成形，而背吃刀量对金属纤维的成形影响最大，切削速度和进给量的影响则不明显。

Then,by mathematics analysis, it prove that the contradiction difficult problem have been quite resolve when cutting clearance angle is zero degree but cutting surface mark deepness theoretics value is zero.

然后通过数学分析，证明在锯料角等于零度而使锯痕深度理论值为零的情况下，两者相互矛盾的难题得到了彻底解决；所做的锯切实验也验证了这一点。

The analysis of these wood sawing technologies are made and the conclusion is that the whole technical performance of zero degree side clearance angle woodworking saw s is better and can realize high quality,high efficient and high profit cutting of wood.

简述木材锯切技术所经历的手工期、简单机械期、近代期和现代期及其特点，对各种木材锯切技术进行了分析，结论是零锯料角木工锯子技术整体性能较好，可以实现高质量、高效率、高效益锯切木材。

Therefore, Fine copper fibers with stability quality were obtained under setting back engagement for 0.04-0.06mm, cutting speed for 30-60m/min and feed for 0.72-1.44mm/str, and using the tool with rake angle and clearance angle were 30° and 8°, respectively.

在背吃刀量为0.04-0.06mm，切削速度为30-60m/min，进给量为0.72-1.44mm/str的条件下选择前角为30°，后角为8°的多齿刀具，可以获得质量稳定的微细铜纤维。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。