查询词典 clearance angle

The wood of China fir and Taiwan zelkova were used for cutting test. Cutting conditions of the tool were rake angle 35°, sharpness angle 29° and clearance angle 26°. Five depths of cut were laboratory fraise for metal cutting. The cutting force measurements, based on the cutting surface of the test material, were performed by a quartz piezoelectric three component dynamometer.

采用杉木与台湾榉之气乾材为试验材料，切削试验以高速度钢材质之平刀进行二次元纵切削(90-0)之平削试验，切削条件中刀具斜度角为35°，刀端角为29°，余隙角为26°，切削深度为0.05、0.1、0.2、0.3与0.5 mm，切削速度为1.1cm/s。

In the analysis of dynamics cutting angle, the following phenomenon is discovered first time: the minimize of dynamics clearance angle is not monotone decreasing with the vibration frequency , and appear peak value periodically, which exist is the disseparation region and approach the separation region.

在对振动钻削中切削刃上各点的动态角度的分析中，首次发现在振动钻削过程中动态后角的最小值不是随着频率或频转比的增大单调下降，而是周期性的出现波峰值，这些波峰值都出现在不分离区，而且是接近于分离区处，这是由振动钻削过程中的变速特性引起的。

A very large 10 clearance angle reduces the strength of the tool tip, and hence normally an angle of the order of 5-6°is used.

过大的后角就减小了刀尖的强度，因此，后角通常为 5～6°。

Clearance angle This is the angle between the machined surface and the underside of the tool called the flank face.

后角 这是已加工表面和刀具下面叫做后刀面之间的夹角。

Results show that the milling tool with rake angle 5°, clearance angle: 10°, helix angle: 45° and corner radius: 1 mm is tested on the surface integrity experiment.

实验结果表明，前角5°，后角10°，刀尖圆弧半径为1mm，铣刀螺旋角为45°的几何结构铣刀完成了表面完整性试验中。

So one more drill point geometric parameter is needed, such as heel clearance angle, chisel edge clearance angle.

为了获得唯一的后刀面廓形，必须增加一个辅助参数。可供选择的补充参数有尾隙角、横刃后角、周边后角、切深后角等。

So one more drill point geometric parameter is needed, such as heel clearance angle, chisel edge clearance angle.

可供选择的补充参数有尾隙角、横刃后角、周边后角、切深后角等。

The important parameters of designed flutes, such as rake angle, clearance angle, are analyzed, and the calculating method of tangential vector, normal vector, and so on, is discussed.

基于刀刃曲线模型和刀槽螺旋面的生成原理，提出了可满足各种设计要求的刀槽螺旋面的几何建模方法，推导了铣刀和旋转锉的多种类型的刀槽螺旋面方程。

Equipment with real-time monitoring, arc, interpolation, helical milling, clearance angle, single angle integrated time for 7-15 seconds.

设备配有实时监控，圆弧、插补、斜铣、单角综合清角时间为7-15秒。

Employing the method of complex helical drill point design,the formula of the clearance angle of inner cut edge for the socket drill is derived and the relationship between the clearance angle and the slantwise angle of the inner cut edge is deduced to innovate the design and manufacture of the socket drill.

通过复杂螺旋面钻尖设计方法导出锪窝钻钻尖内刃后角公式及内刃后角与内刃偏角的关系表达式，改进了锪窝钻的设计与制造。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。