查询词典 clash gear

The transmission case is used to change the speeds of rotary disd and elevator, it consists of friction clutch, shift gear and transfer gear.

变速箱的用途是改变转盘、升降机的转速，它包括摩擦离合器、变速机构和分动机构。

The balls actually serve two purposes: first, they reduce friction and wear in the gear; second, they reduce slop in the gear.

这些钢球实际上有两个目的。其一，可以减少传动时的摩擦和磨损；其二，钢球可以减少转向盘的自由行程。

That the curves of the normal force and friction force between two corresponding gear teeth in a given condition can supervise the design and optimization of gear system.

得到了某一特定传动条件下单对齿轮轮齿法向力及齿间摩擦力的变化规律曲线，从而可以指导齿轮系统的设计和优化。

Based on the measurement of noise of an idling lathe C630,the effects of gear tooth friction on change gear noise ,and the relation between friction excitation frequency and gearing frequency were analyzed.

结果证明：齿面摩擦对齿轮振动的激励频率是啮合频率的2倍，可以利用适当的润滑有效地抑制齿轮噪声的高频成分。

This is because the angle on the worm is so shallow that when the gear tries to spin it, the friction between the gear and the worm holds the worm in place.

这是因为，蜗轮蜗杆的升程角很小，当涡轮要带动蜗杆时，蜗轮蜗杆间的摩擦力把蜗杆锁住了。

The working principle of spring friction draft gear for heavy haul freight cars was introduced,and a virtual prototype model of spring friction draft gear was established based on the ADAMS software.

介绍了重载货车弹簧摩擦式缓冲器的工作原理，采用ADAMS多体动力学仿真软件搭建了弹簧摩擦式缓冲器的虚拟样机模型。

Based on the measurement of noise of an idling lathe C630,the effects of gear tooth friction on change gear noise,and the relation between friction excitation frequency and gearing frequency were analyzed.

以一台C630车床空转噪声的测试数据为依据，分析了齿面摩擦对车床挂轮噪声的影响，以及摩擦激励频率与齿轮啮合频率的关系，并通过涂油润滑降低挂轮噪声的实验对此进行了验证。

However, the influence both ship hull deformation and friction between gear teeth are omitted in strength calculation of gear driving fixed in boat in traditional design.

算例表明，船体变形及齿间摩擦时齿轮强度的影响的确不可忽视。

Involute gear ; friction coefficient between teeth ; tooth number ; driven gear ; output torque ; fluctuation ratio

渐开线齿轮；齿间摩擦系数；齿数；从动轮；输出扭矩；波动率

The main identifying characters of wear particle on the ferrogram such as dimension,distribution,quality,component and form of the wear particle were generalized for the three friction couples of gear case including gear,bearing and sliding contact which is in the different phases of running-in wear,normal wear and abnormal wear and in the different degrees of overload,over-speed and fatigue.

介绍了铁谱分析的原理、样品的制备方法和铁谱分析的步骤，概括了齿轮箱齿轮、滚动轴承、滑动接触3种主要摩擦副在磨合磨损、正常磨损、异常磨损3个阶段的磨粒的主要识别特征，包括尺寸、尺寸分布、数量、成分和形貌等。

Methods Clinical data of 3 cases of bile duct injury during laparoscopic cholecystectomy were analyzed retrospectively.

回顾总结3例LC术中胆管损伤的临床资料，分析3例胆管损伤的原因及对策。

These techniques are applied to the gobang.

本文将这些技术用于五子棋中。