查询词典 circuit

This paper introduced an eigen-mode decomposing method to decouple zero sequence parameter in double circuit. The decomposing matrix of eigen-mode component is given. The zero sequence component relationship between voltages or currents at two terminals of double circuit was achieved by composing eigen-mode components.

提出一种采用特征模量分解方法对同杆多回线间的零序参数解耦，并给出了同杆双回线零序参数特征模量分解矩阵，通过特征模量分解得到同杆双回线路两端之间的零序电量关系。

Aiming at the defects on structure design, electromagnetic design, analysis simulation, optimization design and control technology, double-action iron core mechanism, feedback-hold circuit of energy-saving capacitor voltage and intelligent control circuit were expounded, which can be a guidance for wide application...

针对目前永磁接触器在结构设计、电磁设计、分析仿真、优化设计与控制技术等方面存在的不足，重点阐述了双动铁心永磁机构、储能电容电压的反馈-保持电路及智能控制电路。为促进永磁接触器的推广应用指出了进一步的研究方向。

The Periscope Drawtube will be bent because of the water resistance in sailing and this bend will cause the error of star measurement. Due to its especial structure, contactless measurement is the only way to measure its bend degree. First this paper introduces the method by linear array CCD based on structure and light path; Second it expatiates linear array CCD work principle and driving scheduling with example of TCD1501C and the driving circuit by CPLD. The output signal of linear array CCD includes common disturbance so the differential amplifier is needed. In order to make the signal adapt to computer processing, a threshold circuit with Schmitt characteristic and the data process following threshold are given. At last, some key problems in application are given.

潜艇潜望镜的镜筒在航行时受到水的阻力会产生弯曲变形，这种变形会造成潜艇对星体测量的误差；由于镜筒结构的特殊性，对其弯曲程度的测量只能采用非接触方法；首先从结构和光路方面介绍采用线阵CCD作为检测元件实现对镜筒弯曲程度的测量；其次以东芝公司的线阵CCD（TCD1501C）为例阐述了其工作原理及驱动时序的控制要点，并介绍了基于可编程逻辑器件的线阵CCD的驱动电路；线阵CCD输出的信号中含有共模干扰，必须采用差分放大器将其抑制；为将信号转化为适合计算机处理的数字信号，文中给出了有一定实用价值具有施密特特性的二值化处理电路及二值化后的数据处理过程；最后阐述了在实际使用中的一些关键问题。

The computer separately connects and controls the I/O end and A/D converter; the I/O end connects and controls the X, Y axis driving circuit and the semiconductor laser; the X, Y axis step-by-step driving circuit connects and controls the X, Y step-by-step electrical machines to control the dimensional platform; the beam of the semiconductor laser passes through the focusing drawtube with 0.1mm diameter to form the facula with the diameter less than 0.1mm; the facula irradiates on the detector surface of the XY dimensional displacement platform to produce the corresponding electric signals; the detector surface connects the A/D converter through the amplifier; the electrical signal is amplified and is converted into the data signal by the A/D converter and is sent to the computer for processing.

由计算机分别连接并控制I/O端口和A/D转换器，I/O端口分别连接并控制X、Y轴步进电机驱动电路和半导体激光器，X、Y轴步进电机驱动电路分别连接并控制X、Y轴步进电机，从而控制二维位移平台，半导体激光器的光束经过设有直径0.1mm小孔的聚焦镜筒形成＜0.1mm直径的光斑，光斑照射于设在XY二维位移平台上的探测器表面使其产生响应的电信号，探测器表面经放大器连接A/D转换器，电信号经放大器放大后，由A/D转换器转换为数据信号送计算机处理。

Introducing the LED driver circuit at the same time, and analyzed several common shortcomings of the drive circuit.

在介绍LED驱动电路的同时，又总结分析了几种基本驱动电路的不足。

A novel driver circuit is presented to solve this problem.A charge pump circuit is used in the design.

文中设计了一种新颖的适用于D类功放的驱动电路，在芯片内部采用一个电荷泵电路。

Purpose: Switching, interface circuit and driver circuit applications.

用途：用于开关、界面电路以及驱动电路中。

Then the paper illustrates the design of IGBT driver circuit and the welding feeder control circuit.

接着介绍了IGBT驱动电路和送丝电机控制电路的设计。

Secondly, the driver circuit, the control circuit, magnetic component of the power supply are designed and optimized.

其次，对开关电源的驱动电路、缓冲电路、控制电路及主要磁元件进行优化、设计。

Based on the principle of ultrasonic cleaning, the working process of the ultrasonic cleaning machine was analyzed including control circuit, driver circuit, frequency tracking,impedance matching and software design.

依据超声波清洗原理，分析了超声波清洗机的工作过程，对超声波清洗机的控制电路、驱动电路、频率自动跟踪技术、阻抗匹配及系统软件设计方法进行了详细介绍。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。