查询词典 circuit

It simulates the circuit breaker with a zero impedance branch, and adopts the linear network characteristic and theory, variable structure and variable parameter analyses to transfer the short-circuit current flow in the bus-bar equality into each side of circuit breaker, and deduces the sequence component model and algorithm for calculating the short-circuit current of circuit breaker when the short-circuit fault occu...

该方法将断路器作为一条阻抗为零的支路来模拟，运用线性网络特性、定理及变结构与变参数的分析方法，将母线上短路时的短路电流等值转移到断路器两侧，导出了相当于在断路器两侧分别发生短路故障时，流过断路器的短路电流的序分量模型和算法。

With this mode of working the base-emitter circuit is the input side;and the emitter through base to collector circuit the output side.although these have a common path through base and emitter, the two circuit are effectively separated by the fast that as far as polarity of the base circuit is concerned,the base and upper half of the transistor are connected as a reverse biased diode.hence there is no current flow from the base circuit into the collector circuit.

这一工作模式下，基极-发射极电路是输入端，发射极通过基极，再到集电极电路的输出端。虽然它们都有一个共同的路径通过基极和发射极，这两个电路是通过和基极电路相关的尽可能的有效快速分离开的，基极和基极以上的一半以上的晶体管作为一个反偏二极管与之相连接。

In Chapter 4, on the basis of the selected CPU chips, the hardware frame of the embroidery machine control system is determined according to the overall framework. The power circuit, reset circuit, memory interface circuit, keyboard and display circuit, USB interface circuit, serial communication interface circuit and nether electromechanical interface circuit are designed in particular.

第四章根据总体架构，在选好的CPU芯片的基础上确定了绣花机控制系统的硬件框架，详细设计了电源电路、复位电路、存储器接口电路、键盘与显示电路、USB接口电路、串行通信接口电路和下层机电接口电路。

The hardware system mainly includes the Hall probe circuit, magnetic-flux meter circuit, extension measurement circuit, data capture circuit, the parameters storage circuit, display and keyboard circuit, serial communication controller circuit etc.

硬件系统主要包括磁场测量、磁通表、伸缩量输入、数据采集、参数存储、显示和键盘电路、通讯接口电路等。

In the course of developing the hardware system, the circuits diagram is finished by the mean of EDA software. On the basis of analyzing function of hardware circuit, choose the AT89C51 as single chip microprocessor. Filter and amplifier circuit, sample and hold circuit, Analog-to-Digital conversion circuit, watchdog circuit, out port control circuit and power supply circuit were designed.

在硬件系统研制过程中，应用EDA软件完成电路原理图的设计，分析了硬件系统的各个组成部分及其功能，选用ATMEL公司的AT89C51单片机作为微处理器，设计了滤波放大电路、采样／保持电路、A／D转换电路、看门狗电路、输出控制电路以及电源电路。

The design of accelerometer/angulometer is based on MSP430FW425 microcontroller and ADXL202 accelerate sensor. Protel DXP is used in circuit design, which completes the schematic and PCB design of modules including the clock circuit, the filtering circuit, the power supply circuit, the communication circuit between MSP430 and PC, ADXL202 collecting signal circuit and LCD display circuit.

硬件部分采用Protel DXP开发平台完成了系统的时钟电路、滤波电路、电源电路、MSP430 与PC机之间通信电路、ADXL202传感器电路、LCD显示电路等的电路原理图和PCB板图设计，完成了硬件实物制作。

First, it analyses all-around design of the electronic computer-based interlocking system and each module, then from introducing CAN bus, it lucubrates design of the censorial module's software and hardware which is based on CAN bus of signal lamp's stimulant state, then the hardware's circuit of the entire system's censorial module is made up of opsonic circuit, collecting circuit, microcontrolled circuit,circuit of communication, interrupt circuit of overcurrenting and reset circuit.

首先对全电子计算机联锁系统的总体设计及各个执行模块进行全面的分析和研究，然后通过介绍CAN总线技术，着重研究了基于CAN总线的信号灯模拟状态监测模块的软硬件设计，其中整个系统监测模块的硬件电路主要由硬件调理电路、采集电路、微控制电路、通信电路、高过流中断电路、复位电路等部分组成。

First, it analyses all-around design of the electronic computer-based interlocking system and each module, then from introducing CAN bus, it lucubrates design of the censorial module%26rsquo;s software and hardware which is based on CAN bus of signal lamp%26rsquo;s stimulant state, then the hardware%26rsquo;s circuit of the entire system%26rsquo;s censorial module is made up of opsonic circuit, collecting circuit, microcontrolled circuit,circuit of communication, interrupt circuit of overcurrenting and reset circuit.

首先对全电子计算机联锁系统的总体设计及各个执行模块进行全面的分析和研究，然后通过介绍CAN总线技术，着重研究了基于CAN总线的信号灯模拟状态监测模块的软硬件设计，其中整个系统监测模块的硬件电路主要由硬件调理电路、采集电路、微控制电路、通信电路、高过流中断电路、复位电路等部分组成。

After this text introduced and will imitate the audio frequency signal processing as numerical signal after red shoot outside, the numerical signal that will receive again solution adjust after the audio frequency power enlarger enlarge restore in order to imitate the speech signal, shot the electric circuit outside analyzed to design the audio frequency signal before collecting the electric circuit, signal placed the big electric circuit, frequency to make the electric circuit, red, red circumscribed to accept the electric circuit,, frequency the solution adjusted the electric circuit and audio frequencies to enlarge the electric circuit etc.

本文介绍了将模拟音频信号处理为数字信号后经红外发射，再将接收到的数字信号解调后经音频功率放大器放大后还原为模拟语音信号，在分析设计了音频信号采集电路、信号前置放大电路、频率调制电路、红外发射电路、红外接收电路、、频率解调电路以及音频放大电路等各组成部分。

This article from the temperature examination electric circuit, a/D switching circuit, the output control electric circuit, the keyboard and LED display circuit's design and so on several aspects embarks, the dissect and has designed based on monolithic integrated circuit's greenhouse big awning observation system's each partial contents, has designed the monolithic integrated circuit and the peripheral circuit, the parallel connection unites the set of complete procedure algorithm.

本文从温度检测电路、A/D转换电路、输出控制电路、键盘及LED显示电路的设计等几个方面出发，详细研究和设计了基于单片机的温室大棚测控系统的各个部分内容，设计了单片机及其外围电路，并结合一套完整的程序算法。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。