查询词典 circuit court

The design of the generator line multiplying automatic synchronizing unit synchronizing unit SID-2CM 's coordinating with several synchronization point sharing synchronizing unit automatic selector switch SID-2X is used in Shanxi Datang International YunGang Thermal Power Co.LTD, realized the No. 1 unit's generator –transformer-line group circuit breaker, high voltage plant transformer circuit breaker, start spare transformer circuit breaker accept change DCS automatic control devices.

山西大唐国际云冈热电有限责任公司采用 SID-2CM 型发电机线路复用自动同期装置与 SID-2X 型多同期点共用同期装置自动选线器配合的设计，实现了1号机的发—变—线组断路器、高厂变断路器、启备变断路器接受 DCS 的全自动控制。

In order to solve the problems of bad shunting and red light strip phenomenon at electric railway section caused by the defective of asymmetric pulse track circuit receiver formerly, a new type of asymmetric impulse track circuit receiver is designed. It takes the PIC16F887 single-chip microcomputer as central processing unit of the system, realizes processing and judging the asymmetric impulse from the track transformer automatically. The article focused on the receiver work flow, hardware circuit and software design.

摘 要：为了解决以往多数不对称脉冲轨道电路接收器存在缺陷而导致的分路不良问题和电气化区段空闲&红光带&现象，设计了一种新型脉冲轨道电路接收器，系统以PIC16F887单片机为核心处理单元，自动实现对由轨道变压器传来的不对称脉冲信号进行处理和判决，重点讨论了接收器工作流程、硬件电路实现以及软件设计。

The dynamic model and equivalent circuit are researched, A dynamic model and equivalent circuit in d-q frame of dual three-phase synchronous machine are presented for the first time, based on the analyzing of the inductance factor between the windings of synchronous machine under ideal conditions. From them, a dynamic model and equivalent circuit that has general significance is educed.

基于理想同步电动机模型，以相绕组为研究对象，对双电枢绕组同步电动机的动态数学模型进行了研究，首次推导出双电枢绕组同步电动机在d-q坐标系的动态数学模型，绘出了d-q坐标系等效电路。

On the basis of instantaneous forced analysis to short circuit of power transformer and numerical value calculation using low voltage impulse analysis, the paper presents the essentiality of winding distortion after short circuit of power transformer. By contrasting the three main ways of the world such as low-voltage impulse、 short circuit impedance analysis and frequency response analysis , FRA is adopted for distortion testing. Then we design a new testing instrument of transformer winding distortion—testing system of transformer winding distortion.

本文首先在对电力变压器短路时的瞬时受力分析及所受电磁力的有限元法的数值计算的基础上，论证了电力变压器短路以后进行绕组变形测试的必要性；然后通过比较的方法对目前国内外主要使用的三种方法：低压脉冲法、短路阻抗法和频率响应法，进行了一一对比，并根据对比结果，确定在本课题中使用频响法；最后在理论研究的基础上，设计出了一种新型的变压器绕组变形测试仪——电力变压器绕组变形测试系统。

First, the design of the hardware circuit: It is mainly the interface circuit of PLC, including operation control signals of inputting part, low-voltage protection,over-voltage measure circuit , sensor input signal ,etc.

第一、硬件电路的设计：主要是PLC的接口电路，包括输入部分的运行控制信号，欠压检测、过压检测电路，传感器输入信号等等，输出部分有悬浮部分的主电路，显示电路，扩展模块以及变频器VDF—M的连接。

The hardware circuit mainly includes master controller,temperature measurement circuit and display circuit.

介绍了一种以AT89C51为主要控制器件，以DS18B20为温度传感器的新型数字温度计设计方法，其硬件电路包括主控制器，测温电路和显示电路等。

In retiming registers are added at some points in a circuit and removed from others in such a way that the functional behavior of the circuit as a whole is preserved. By retimng we can optimize the speed, area or power of the circuit.

重定时在保证功能不变的前提下，通过移动时序元件的位置和改变时序元件的个数来优化同步时序电路的速度、面积和功耗。

A superimpose d circuit derived from two suitably arranged pairs of wires called side circuits,with each pair of wires being a circuit itself and at the same time acting as one conductor of the phantom circuit.

一种由称作半边电路的两对线路经适当安排形成的叠加电路。每一对线本身既作为电路，同时又充当幻象电路的一个导体。

A superimposed circuit derived from two suitably arranged pairs of wires called side circuits, with each pair of wires being a circuit itself and at the same time acting as one conductor of the phantom circuit .

一种由称作半边电路的两对线路经适当安排形成的叠加电路。每一对线本身既作为电路，同时又充当幻象电路的一个导体。

The printed circuit assembly is IR or convection reflowed at a temperature between approximately 280 and 290 degrees C, and maintains solder connection integrity when the printed circuit assembly (36) is later incorporated into a second printed circuit assembly using a standard tin-lead solder system.

该印刷电路组件在约280―290℃的温度下通过IR或对流加热而发生回流，并且当该印刷电路组件（36）随后通过标准的锡―铅焊料系被安装至第二印刷电路板时维持焊料连接整体性。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48