查询词典 cavity
- 与 cavity 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The shell body of slip-jaw clutch is a disk with complicated cavity, it is difficult to process the complicated cavity.
中文摘要:超越离合器壳体是一种具有复杂内孔型腔的盘状类零件,其异型型腔的加工非常困难。
-
The crystal defect was observed and analyzed. Room temperature Nd:NYW crystal samples sized 3x3x5mm and 5x5x5mm were LD pumped at 808nm plane-concave cavity and double-concave cavity laser systems respectively, 1060-1064nm has been demonstrated.
室温下,分别用平一凹腔系统对尺寸为3×3×5mm的Nd:NYW激光晶体,用双凹腔系统对尺寸为5×5×5mm的Nd:NYW的激光晶体进行连续激光输出实验。
-
Result: B-2 can increase abdominal cavity macrophage phagocytic activity significantly (p.001) B-1 can increase abdominal cavity macrophage phagocytic activity (high dose of B-1: P.01, low dose of B-1: P.05). Only high doses of S. sphenanthera coarse polysaccharides can increase phagocytic activity (phagocytic index p.05) and show dose-dependent augmentor effects.
结果:北五味子脱蛋白粗多糖能极显著增强腹腔巨噬细胞吞噬功能(p.001),未脱蛋白粗多糖能显著增强腹腔巨噬细胞吞噬功能(大剂量组p.01、小剂量组p.05),而南五味子粗多糖只有大剂量组能增强腹腔巨噬细胞吞噬功能(吞噬指数p.05),并呈一定的量效关系。
-
Aim: Investigation of the influence of the corticoid injected into the epidural cavity for the treatment of prolapsed lumbar intervertebral disc on the local tissues in the spinal cavity.
通过EB组 40例、非EB组 2 0例腰椎间盘突出症手术切除的黄韧带及椎间盘组织的组织学观察,以及前者 1 2例、后者 1 0例电镜超微结构观察的结果进行比较。
-
The method includes the steps of gripping the peripheral edge of the fabric in a stretching assembly, activating the stretching assembly to stretch the fabric in a location adjacent to the mold assembly, clamping the stretched fabric against a face of the mold assembly, releasing the peripheral edge of the fabric from the stretching assembly, moving the stretching assembly from the path of the mold assembly, closing the mold assembly on the fabric with the peripheral edge of the fabric terminating in the mold cavity and injecting molten material into the mold cavity to form the frame directly on the peripheral edge of the fabric.
方法包括的步骤为在拉伸装置中夹紧纤维织物的外围边缘、在邻接浇模装置的位置启动拉伸装置来拉伸纤维织物、贴着浇模装置的面夹住已拉伸的纤维织物、从拉伸装置释放纤维织物的外围边缘、从浇模装置的轨迹移动拉伸装置、在纤维织物上闭合浇模装置并使同纤维织物的外围边缘终止在浇模空腔中和将熔化的材料注射到浇模空腔中以在纤维织物的外边缘直接形成框架。
-
Carrying gases are fed into three ways of powder hopper, feed wheel cavity and falling powder cavity respectively.Many tests of pneumatic powder transport were done for evaluating this device with Ni45 and WC.
选用Ni45、WC两种不同典型料性的合金粉末应用该装置进行了气动送粉试验,对送粉器的性能进行了测定,获得了理想的效果。
-
The sprue puller, being attached to the moving half, is pulled through the floating cavity plate and thereby releases the feed system which is then free to fall between the floating cavity plate and the feed plate.
位于动模上的拉料杆离开浮动型腔板并且藉此释放浇注凝料,然后它在浮动型腔板和定模板之间自由落下。
-
Often in the foot or mantle visceral mass, the formation of a cavity connected with the outside world, known as the "mantle cavity."
外套膜常在足部或内脏团间,形成1个与外界相通的空腔,称为&外套膜腔&。
-
The simulation results show that the asymmetry structure of the ratchet die cavity influences the BMG's flowing behavior greatly. During the material filling tooth cavity, dead zone volumes exist and situate on the areas with sparse teeth distribution. The full filling or not of the ratchet tooth tips, as the final filling region of the forming process, determines the super-plastic forming quality. Adopting smaller punch speed or longer load holding time is necessary for full filling of the tooth tips.
研究结果表明,棘轮模腔结构的不对称性对材料的流动行为影响显著;在材料向齿形的充填过程中存在流动死区,死区的位置处于齿形分布较稀疏的部位;齿形尖角是成形的最后充填部位,在终成形阶段采用较小的压下速度或较长的保压时间,有利于齿形尖角的完全充满。
-
First to analysis original data, including the properties of the material and technological characteristics of the plastic part, then decide the divide surface of cavity and the arrange way of mold cavity, designing the side take out core outfit and guide runner and slide block, still ca
首先分析原始资料,包括塑件材料的性能和结构工艺特点,然后确定分型面和型腔排列方式,接着设计侧抽芯机构以及导滑槽和滑块,还对成型零件、型腔壁厚、加热和冷却等进行了计算,最后对注塑机进行校核。
- 相关中文对照歌词
- Cavity King
- Cavity Search
- 推荐网络例句
-
I didn't watch TV last night, because it .
昨晚我没有看电视,因为电视机坏了。
-
Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.
今年以来,在北京的很多小区里,电梯液晶电视被撤了下来。
-
I'm running my simile to an extreme.
我比喻得过头了。