查询词典 cast

This paper has reviewed and analyzed the development of China's iron cast technologies in cupola smelting, electric furnace smelting and various cast iron alloys, and forecast its prospects in future.

本文从冲天炉技术、电炉技术和铸铁合金等方面回顾和分析了我国铸铁铸造技术的发展，并论述了未来的发展方向。

At the same time, the company also has production JP low-voltage distribution cabinets, power station control cabinet and all kinds of distribution box, and is supporting the transformation of rural power equipment manufacturing plant, the company has a casting factory, with a large cupola furnace, Mixer, Shot casting machines and other equipment and testing equipment, capable of producing various grades of gray cast iron, wear-resistant cast iron, ductile iron castings.

同时公司还具备生产JP低压配电柜，电站控制柜及各种配电箱的能力，是农村电网改造配套设备的生产厂，公司设有铸造分厂，具有大型化铁炉，混砂机，喷丸机等铸造设备和检测设备，能生产各种牌号的灰口铸铁、耐磨铸铁、球墨铸铁铸件。

By means of high speed gas stream compound with coaxial cutting gas for pulsed Nd:YAG laser on cutting of ceramics,the technological parameters affected on the thickness of re cast layer and the exiting of crack in re cast layer were studied.

针对激光切割陶瓷产生的重铸层和裂纹，设计了超音速喷嘴，采用侧吹高速辅助气流与同轴切割气流复合技术，研究了激光加工工艺参数对重铸层及裂纹的影响规律，开发了获得最小重铸层厚度和裂纹长度的高效率激光切割方

Key products include: cast iron plate, cast iron platform, the test platform, crossed platform, Maohan platform, fitter platform, table, Ping-foot, to me, V-type, V-iron, right-angle-foot, V-iron, foot bridge , Curved panels, machine damping Sizing Block, adjusted Sizing Block, partial-place, Jack, special wrench, gear Gear beat Tester; platform granite, marble slab, Ping-foot, V-iron, to me, Jiaochi, V-shaped blocks, such as platform support.

主要产品包括：铸铁平板、铸铁平台、检验平台、划线平台、铆焊平台、钳工平台、工作台、平尺、方箱、V型架、V 型铁、直角尺、V型铁、桥尺、弯板、机床减震垫铁、调整垫铁、偏摆仪、千斤顶、特种扳手、齿轮齿圈跳动检查仪；花岗石平台、大理石平板、平尺、V型铁、方箱、角尺、V型块、平台支架等。

Finally, several sets of cast dies and molds, including V6 transfer mold emplyed by GM, shoe die and piston die used for Santana, have been casted by LS high precise die-making system. All of these dies only needed a little machinaity. The cost and manufacture period of cast dies are lower than those of traditional wrought dies.

最后，采用LS法精密模具制造技术，用铸铁和新开发的铸造模具钢MCH13钢浇铸了多副模具，如V6发动机曲轴模、鞋模、桑塔纳轿车用活塞模具等，这些模具仅需进行少量的机加工即可进行使用，其生产成本及制作周期大大低于同类传统方法制造的模具。

For the first time at Land Rover, the blocks are high pressure die-cast rather than sand-cast, providing a superior finish and dimensional greater accuracy.

第一次在路虎，该区块的高压压铸而非砂铸造，提供了卓越的成绩和尺寸更大的准确性。

Systematic research about technology parameters influences on the magnetic properties and microstructure of theses magnets have been done. The better parameters of production have been achieved. They are showed as follows: as-cast alloys with the nominal composition Nd15Fe78-xNbxB7 are prepared by induction-melting under argon atmosphere. As-cast alloys are broken under argon atmosphere and filtered through 40# screen. The coarse grain is ball-milled under 120# avgas for 80 min. The ratio of milling ball and grain is 15:1. Then fine powder is aligned and pressed in a magnet field of 1.5T. The pressure is 80MPa. The green compacts then are shaped by cold isostatic pressing under 280MPa pressure.

通过研究具体工艺参数对磁体磁性能及显微结构的影响，总结出适合于该系列磁体的制备工艺如下：按设计成分将原料放入真空感应熔炼炉内进行合金铸锭的熔炼；合金铸锭在高纯氩气保护下粗破碎过40目筛；以15∶1的球料比在120#航空汽油的保护下滚动球磨80min；球磨好的磁体粉末在1.5T取向磁场下以80MPa的压力模压成型，接着在280MPa压力下进行冷等静压；所得的压坯在1110℃烧结1h，900℃回火处理1h，600℃回火处理2h。

This paper introduces a type of composed water-tube boiler that is fitted with a new type of cast iron air heater instead of the common cast iron economiser.

本文介绍了组装式热水锅炉，采用新型铸铁空预器代替省煤器，可以克服省煤器缺点，加热空气，强化炉内燃料的燃烧，回收余热，从而达到提高锅炉热效率，增加出力的目的。

Since an Aimed Shot would fire (3-second cast time) and be followed by an autoshot as well as a global 1-second cooldown (3 cast plus 1 cool = 4 seconds total), the Multi-shot would be available to fire at the ten-second mark.

因为一个瞄准射击发出后（3秒施法时间）紧接着会有一发自动射击射出而所需的时间就像1秒的公共冷却（3＋1＝4秒），这之后也就是第10秒多重射击将可以再次使用。

The major content of this thesis are as follows:1 Performed FEM analysis before strengthening, and to find out the reason for the cracking and present a strengthening scheme;2 Performed nonlinear FEM analysis before and after strengthening, and to get the varying rule of the relative displacement between the on-site cast concrete side wall and that between the precast concrete arch and the floor, as well as the stress distribution of the gallery;3 Performed on-site observation experiments on the 7~th gallery, and to get the varying rule of the relative displacement between the on-site cast concrete side wall, as well as that between the precast concrete arch and the floor.4 The results of the computation were compared with those of experiments, which verified the effect of the strengthening.

本文的主要工作有： 1 对加固之前的廊道结构进行有限元计算，找出廊道底板开裂的原因，提出加固方案； 2 对加固前后廊道结构进行非线性有限元计算，得到加固前后廊道两现浇边墙相对位移、拱顶与底板相对位移随水库水位变化的规律和廊道结构的应力分布情况； 3 进行廊道加固前后现场观测试验，得到廊道两现浇边墙相对位移以及拱顶与底板相对位移随水库水位变化的规律； 4 对比分析加固前后现场观测试验与非线性有限元计算所得结果，论证加固方案的合理性，验证加固效果。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了