查询词典 cartridge filler

Remove extra joint filler on the surface of tiles.

勾缝后应用瓷砖表面多余的嵌缝料擦拭干净。

Properties of vacuum brazed Si3N4/steel Joint using active brazing filler metal.

活性钎料真空钎焊Si3/N4钢接头性能的研究。

The remelting temperature of 1Cr18Ni9Ti stainless steel joint brazed with the nickelbase filler metals is investigated by the use of both the microstructure analysis and the differential thermal analysis.

在钎焊过程中，熔化的钎料与不锈钢相互作用，使得焊后钎缝的成分不同于所用钎料的成分，钎缝的重熔温度也不同于钎料的熔点。

Function: Joint filler for external thermal insulation system.

用 途：适用于外墙外保温体系瓷砖的勾缝，适用缝宽1-12mm。

Stress concentration zones and the maximum value of thermal stress of the TiC cermet/iron joint brazed with Ag-Cu-Zn filler metal during cooling were studied in this paper.

本文研究了采用Ag-Cu-Zn钎料在1173K温度下钎焊TiC金属陶瓷与铸铁挺柱实际件时，在冷却过程中接头处的应力集中区和热应力最大值。

During application, fill both sides with joint filler, and then fill middle part and press.

施工时，宜用镘刀或腻子刀施工，小心涂抹，先使嵌缝料满粘两侧，再填满中间；然后压平，或用塑料或竹木溜子压成半幅面状。

The remelting temperature of 1Cr18Ni9Ti stainless steel joint brazed with the nickelbase filler metals is investigated by the use of both the microstructure analysis and the differential thermal analysis.

利用金相试验和差热分析方法，系统地研究了用镍基钎料钎焊1Cr18Ni9Ti时钎缝的重熔温度随钎焊工艺变化的规律。

The result indicated that the stress was concentrated on the end of the joint interface and inner filler metal. If brittle intermetallics were produced in these areas, the fracture of joint would occur frequently.

通过采用Marc非线性有限元软件，对接头区在冷却过程中的应力变化、应力分布及裂纹敏感区域等进行了分析。

Finally, when painting used as finishing layer, the area of EPS board should not be less than 40%, and the flex-waterproofing putty and the elastic painting should be used; when tile used as finishing layer, the area of EPS board should not be less than 80% and the special tile adhesive mortar and the joint filler should be applied.

饰面为涂料时，聚苯板粘结面积不少于40%，应使用柔性耐水腻子和弹性涂料；饰面为面砖时，聚苯板粘结面积不少于80%，应采用专用面砖胶粘剂和勾缝砂浆进行施工。

High purity alumina ceramics were brazed to niobium metal to analyze the effects of brazing temperatures and Ti content in the active AgCuTi alloy filler on the joint microstructure,interfacial reactions and shear strengths.

为了确定高纯氧化铝陶瓷与金属Nb 的直接钎焊工艺参数，采用AgCuTi活性钎料，研究了钎焊温度和钎料中的钛含量对接头组成、界面反应以及接头剪切强度的影响。

Alternatively, the con- trollers can use the synchronous rectifier itself or loss- less inductor current-sensing methods to provide overload protection with lower power dissipation.

另外，康威特罗勒斯可以使用同步整流器本身或亏损减少电感电流检测方法，以提供低功耗过载保护。

Mr. Dauber's other Schatz hangs in his home movie studio.

多伯把沙兹的另一件作品挂在家里的电影室。