查询词典 cartridge filler

Ag-Cu-Ti active filler metal exhibits a good wettability to brazing c-BN, joint interface between filler metal and c-BN is compact, and a reaction layer is formed between them.

Ag-Cu-Ti活性钎料对c-BN的润湿性较好，界面结合紧密，并在界面处形成反应层。

The results demonstrate that welds with good appearances could be obtained when welding with the appropriate processing parameters. The as-welded joint tensile strength without filler wire is 180.7 MPa, while the tensile strength is 190 MPa when welding by one side with the filler wire of AlSi12 or AlMg4.5MnZr.

研究结果表明，在合适的工艺参数下，可以获得表面光洁、正反面焊缝成型良好的对接接头；焊态下，单面焊接不填充焊丝的接头强度为180.7 MPa；单面焊接填充AlSi12，AlMg4.5MnZr焊丝的接头强度最低为190 MPa，且两种填充焊丝接头的拉伸强度无明显差异；双面焊接填充AlMg4.5MnZr焊丝的接头强度达到200.7 MPa，约为母材的90%。

Using high frequency induction brazing and TiZrNiCu filler metal, the shear strengths of the joints were low. The maximum shear strengh was only 102.1MPa, which was lower than the maximum strength of vacuum brazing. The reasons may be that excessive intermetallics, holes and oxidation existed in the joint. So TiZrNiCu filler metal isn't fit for non-vacuum brazing.The stress variation, stress distribution and crack-sensitive regions during the cooling process of brazing have been studied by Marc non-linear software.

采用气体保护高频感应加热、TiZrNiCu钎料钎焊时，接头的强度普遍偏低，最高的剪切强度只有102.1MPa，远远低于辐射加热真空钎焊的强度，其原因是接头中局部生成了过量的金属间化合物，且产生氧化，接头中含有较多的气孔等影响了接头强度，因此可以认为TiZrNiCu钎料不适合在非真空条件下的钎焊。

Thecompounds were dispersed in the melted silver-based brazing filler metal inamorphous particles as nucleators of heterogeneous nucleation, so that made themelted filler metal form Ag and Cu solid solution as well as Cu solid solutioncontaining CePb or CeBi and that eliminated the negative effects caused by Pb orBi.

通常情况下它们以无定性态存在于银基钎料中，成为非均匀生核的生核剂，使银基钎料形成银固溶体+铜固溶体+含CePb或CeBi化合物的铜固溶体相，从而消除了 Pb或Bi的有害影响。

After latex wood filler coat 20 has been applied over crackle medium 18, if desired the wood filler coat may be embossed with designs 22 as shown in FIG.

乳胶后木材填料大衣20已应用于超过18裂纹中等的话，木材填料大衣可浮雕图案22所示体操。

The air operated quota kinking sausage filler uses the control valve switch air cylinder to adjust the processed products respective weight, the button achieves through the operation kneading board on controls each procedure movement the goal, this equipment is the sausage equipment which performs in the quota sausage filler's foundation to develop, this machine both could the quota sausage and be able the automatic kinking, to change the insufficiency which the past quota sausage kinking could not one time complete, this machine stable property, the operational safety was reliable, raised the production efficiency in the original foundation.

气动定量扭结灌肠机，采用控制阀开关气缸来调整加工产品所属重量，通过操作面板上按钮达到控制各个程序动作的目的。该设备是在定量灌肠机的基础上加以研制的灌肠设备，该机既能定量灌肠又能自动扭结，改变了过去定量灌肠扭结不能一次完成的不足，该机性能稳定，操作安全可靠，在原有的基础上提高了生产效率。

The HA sinter with optimal strength and porosity could be obtained when HA was mixed with 1 of fold sucrose which was used as filler while binder and 1 of fold salt as filler, pressed under 5-45 kgf/cm2 force, dissolved the sucrose at 220°C, and then sintered under 1345°C for 10h.

目前得到，使用砂糖及食盐当作填充剂，以HA比砂糖比食盐为1比1比1，5-45 kgf/cm2的压力压制成形，再以220°C下加热使砂糖溶解，并且在1345°C烧结10小时的烧结物的强度以及孔隙度为最佳。

a new high temperature anti-static coating was prepared using inorganic acid aluminum phosphate binder for the film-forming material, fused quartz powder for high temperature resistance filler, OP-10 for non-ionic surfactant, magnesium oxide and zinc oxide as a curing agent, tin oxide for conductive filler.

以酸性磷酸铝无机黏结剂为成膜物，电熔石英粉为耐高温填料

Hirohito filler letter Jiangxi Chemical Equipment Co., Ltd. is currently the larger of the new chemical filler.

江西省裕仁信化工填料设备有限公司是目前国内规模较大的新型化工填料。

We have been selling our products to many countries like Europe, Middle East, North Africa and Association of South East Asian Nations etc. Our product was produced and tested according to the International quality standard, high water-pressure water test and high air-pressure seal test to make sure no leakage of the products, high quality material, glossy polishing, advanced plating technology and equipment, with cartridge of usage design standard over 300 thousand times.

我们有我们的产品已销售到许多国家如欧洲，中东，北非和东南亚国家联盟联合国等我们的产品是生产和测试按照国际质量标准，高水压力水试验和高气压密封试验，以确保没有泄漏的产品，高品质的材料，光滑抛光，先进的电镀技术和设备，墨盒的使用与设计标准超过300万次。

Alternatively, the con- trollers can use the synchronous rectifier itself or loss- less inductor current-sensing methods to provide overload protection with lower power dissipation.

另外，康威特罗勒斯可以使用同步整流器本身或亏损减少电感电流检测方法，以提供低功耗过载保护。

Mr. Dauber's other Schatz hangs in his home movie studio.

多伯把沙兹的另一件作品挂在家里的电影室。