查询词典 carbides

It is showed that type and morphology of eutectic carbides can be controlled by combining alloyed elements.

结果表明，共晶碳化物的类型和形态能通过合金成分组合控制。

The TiC/Cr18Ni8 steel bonded carbides were in situ synthesized by vacuum sintering with mixed powders of iron,ferrotitanium,ferrochromium,colloidal graphite and nickel as raw materials.

钢结硬质合金是以钢为粘结相，以碳化物为硬质相，采用粉末冶金方法制备的一种介于工具钢和普通硬质合金之间的铁基复合材料。

It was found that lead oxides (including PbO and Pb〓O〓) reacted chemically with PTFE when heated in vacuum, generating PbF〓, element C, and lead carbides.

研究表明，铅氧化物（包括黄色氧化铅PbO和红色氧化铅Pb〓O〓）在无氧加热条件下均能同PTFE发生化学反应，生成PbF〓、单质C以及铅的碳化物。

This article studies the effects of rare-earth modification on carbides pattern,distribution,matrix graininess of high Cr cast iron roller.

本文研究了稀土变质处理对高铬铸铁轧辊的碳化物的形态、分布和基体晶粒度的影响，认为稀土元素在适量的范围内，可提高这种轧辊的冲击韧性、抗压强度、抗剥落性能。

The internal stress and defects decrease with the increase of heat treatment temperature and this makes magnetic domains wider and more orderly but the carbides containing Ti precipitate along the grain boundaries which cause local components and structure heterogeneousness in these areas .

热处理温度越高，组织内应力和缺陷的减少使得磁畴的排列越来越整齐，磁畴宽度也越大，但晶界附近少量含Ti碳化物析出，导致局部成分和结构的非均匀化，不仅使得该区域磁畴细化，而且阻碍了畴界的移动，从而影响了阻尼性能的提高。

The transition metal carbides were a new class of catalysts which had good catalytic activity and selectivity and were widely used in hydrogenolysis,dehydrogenation,desulfidation,denitrification,reforming,and other hydrocarbon conversion reactions.

过渡金属碳化物作为一种催化新材料得到了人们广泛的关注，在催化加氢、脱氢、脱硫、脱氮和重整等方面，表现出优良的催化活性和选择性。

The improvement of the frictional resistance is mainly due to the effect of carbon on residual austenite and the morphology of carbides, and an appropriate amount of residual austenite is helpful to improve the impact toughness and hardness of matrix; The spherical VC can hinder the initiation and propagation of crack and improve the frictional resistance.

碳含量对耐磨性的影响主要是通过对基体残余奥氏体量和碳化物形态表现出来的，适量的残余奥氏体使基体具有较好的冲击韧度及硬度；形态较为固整的VC颗粒，对裂纹的萌生及扩展起阻碍作用，从而使材料的耐磨性提高。

The inserts are large with an iC, inscribed circle diameter, of 19 mm and a thickness of 6 mm with a composition of 5-10 wt-% Co, 5-12 wt-% cubic carbides or carbonitrides of the metals Ti, Ta and/or Nb, and balance WC with a stratified binder phase enriched surface zone 15-40m thick.

刀片很大，其内接圆直径iC≥19mm，厚度≥6mm，其组分为：5-10wt％的Co、5-12wt％的金属Ti、Ta和/或Nb的立方碳化物或者碳氮化物，并且其余为WC，分层富粘结相表面区域为15-40μm厚。

On the other hard, intergranular carbides also increase the stress sensitivity of creep rate and creep activation energy.

利用该模型和单相合金的数据不仅能预测晶界析出合金的蠕变速率而且能导出后者的应力指数和激活能。

The size of microalloyed carbides is very small and some is only 2~3nm. So microcrack extending can be restrained.

并且，由于微合金碳化物尺寸很小，可达2～3nm，对于微裂纹扩展有一定的约束作用。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。