查询词典 carbides

Results also reveal that the contact angle declines continuously with the increase of addition of carbides,and simultaneously the contact angle declines continuously with the increase of the bond energy of ceramic phases.

研究还发现，碳化物的添加使体系接触角持续下降，同时接触角随键能的增加持续下降。

Cemented carbides product: Cemented carbides saw, blade, tool, drill bit, mould, Spray nozzle, seal, muzzle, hammer, Roller, rock drill, Semi-finished materials, Indexing blade, stick materials, long thin slice, plate, denticle piece, Impact drill, Ball, wooden blade, Ramming Mould, Valve, Boat pan and other products.

硬质合金制品：硬质合金圆锯片、刀具、工具、钻头、模具、喷嘴、密封件、顶锤、轧辊、钎具、坯料、可转位刀片、棒材、长条薄片、板材、锯齿片、冲击钻片、球、木工刀头、拉拔冲压模体、阀门、舟皿、非标准耐腐耐磨结构件及各种非标硬质合金制品、其它深加工产品

TiC/Cr19Al3 steel bonded carbides were prepared by in-situ synthesis taking ferrotitanium, ferrochromium, iron, carbon powders as raw material, and the microstructure of the steel bonded carbides was analyzed.

以钛铁粉、铬铁粉、铁粉、胶体石墨等为原料，原位反应生成TiC/Cr19Al3钢结硬质合金，并对所制备的试样进行组织结构分析。

Second phase strengthening theory and carbon depletion in solid solution matrix Here the second phase includes pure carbides and complex carbides which nucleated on oxides in the deposited metal.

在Fe基熔体中，TiC、NbC比ZrC更易于由液态金属中析出，Nb、Ti在800℃以上几乎全部形成碳化物；而VC的液态析出需要极高的浓度条件，但VC在800℃以下的二次析出作用明显。

Creep cracks seem always to initiate at inherent casting pores and slowly propa-gate anisotropically along the (001) planes, perpendecular to axis of stress applied, upto the final fast fracture. Creep cracks can also nucleate at fractured carbides or at in-terfaces between carbides and matrix in the alloys containing more carbon.

结果表明：单晶的蠕变断裂具有明显的晶体学特征，蠕变裂纹总是从已有的铸造的显微疏松处萌生；对于含碳量较高的材料，碳化物及其与基体的界面也是裂纹萌生的有利位置；这些已萌生的裂纹在外加应力轴垂直的(001)面上各向异性地扩展，直到由于承载截面的逐渐减小而导致最终破坏。

The results show that the modificator Mg can cause thermodynamic undercooling , and it may absorb in the crystal faces of preferential growth of carbides, which can slow down carbides growing up on plate type and make them tend to be fine, isolated and passivated, and thus the impact toughness is improved greatly.

研究结果表明：在过共晶高铬白口铸铁结晶过程中，变质元素Mg不仅造成热力学过冷，而且Mg可能吸附于碳化物择优长大的晶面上，起到阻碍碳化物片状长大的作用，使碳化物趋于细小、孤立，且边部钝化，使冲击韧度显著提高。

Fine carbides precipitated from ferrite in 16-6 Cr-Mo, 16-2.5-6 Cr-Ni-Mo, and 16-5-6 Cr-Ni-Mo steels in the early stages of ageing are metastable, during prolonged heating they redissolve and are gradually replaced by χ-phase. Some residual carbides serve as the nuclei of the growing χ-phase. The structure of quenched 16-15-6 Cr-Ni-Mo steel is austenitic, during subsequent heating only M_6C and M_(23)C_6 mixed carbides are precipitated.

在16-6Cr-Mo、16-2.5-6及16-5-6Cr-Ni-Mo不锈钢中，从铁素体内沉淀出来的细小碳化物是一种过渡组织，在x相的成核与长大过程中，它们将不断地进行溶解。16-15-6 Cr-Ni-Mo不锈钢属奥氏体型，在不同温度进行固溶处理，奥氏体都很稳定，在随后的恒温处理过程中，只有碳化物从奥氏体内析出。

Some important questions are discussed, such as, the common characteristics and distinctions of the surface ripples on the (001) surfaces of the carbides, the effects of the surface ripple on the surface energy and the surficial charge distribution, the change trends of the cohesive energy and surface energy of the carbides and their surfaces, an...

讨论了不同碳化物表面褶皱的共同特征和相互差别、碳化物表面褶皱的产生对表面电子分布情况和表面能的影响、碳化物的结合能和表面能的变化趋势、以及表面能与结合能之间的关系。提出了块体结合能和表面褶皱程度两种因素共同影响和决定IVB和VB过渡族金属碳化物(001)表面能的观点。

The results indicate that the main separating phases include borides, carbides and silicides, of which the borides and carbides are dispersion strengthening phases while the silicides mainly improve technological properties of the vacuum melting process.

结果表明，镍基合金涂层中的析出相主要有硼化物、化物和硅化物，其中硼化物、化物起强化作用，硅化物改善涂层熔结过程中的工艺性能。

The microsturcture characteristics of M2 cast-strip were studied with such experimental methods as metallographic analysis, SEM, XRD and TEM[0]. The effect of sub-rapid solidification on the size, type and distribution of eutectic carbides in M2 cast-strip was analyzed. The effect of heat treatment temperature and its holding time on the eutectic carbides in M2 cast-strip was explored. The eveolution of metastable phase of M2C eutectic carbide during the heat treatment period and the decomposition dynamics concerned were researched. The M2 cast-strips were rolled into thin strips and the effect of deformation ratio on carbides in M2 cast-strip was examined. Then these thin strips were comparied with those that were produced by conventional technology on carbide, hardness, red-hardness and bend strength. At last the rolled M2 cast-strips were made into saw blades and their cutting performance was experimented on in tools factories and then compared with that of similar products produced by conventional technology.

采用常规金相、扫描电镜、X射线衍射及透射电镜等实验研究了M2高速钢铸带的凝固组织特征，分析了亚快速凝固对铸带中的共晶碳化物的析出类型和尺寸以及分布的影响；探索了后续热处理温度和保温时间对铸带碳化物组织的影响规律，分析了铸带中的亚稳相M2C共晶碳化物在热处理过程中的分解情况以及分解动力学；将铸带热轧成薄带，研究了压下率对铸带碳化物组织的影响，并将热轧薄带与常规工艺生产的相同规格的M2高速钢薄带在碳化物组织、硬度与红硬性以及抗弯性能等方面进行了对比；将热轧薄带加工成机用锯条后在工具厂进行了锯切性能试验，并与常规工艺生产的同类产品进行了使用性能对比。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。