查询词典 carbide

An intermediate template route was developed to grow cubic silicon carbide nanorods at relatively low temperature of 600~700℃ using tetrachloroethylene (C2Cl4) and silicon tetrachloride (SiCl4) as carbon and silicon sources, respectively by a solvothermal method.

采用中间模板路线在600~700℃相对低的温度下，用四氯乙烯和四氯化硅作为原材料，用溶剂热的方法合成了立方相的碳化硅纳米棒。

The main products are: turning tool, milling cutter, hole processing tool roll pressure tools, machine tool accessories, boring-type CNC milling toolholder, carbide measuring.

主要产品有：车削刀具，铣削刀具，孔加工工具，滚压工具，机床附件，镗铣类数控刀柄，硬质合金量具。

The matrix structure of composition is WC, W2C, M7C3, M23C6, M6C, M12C carbide and Troostite.

复合层组织为：WC、W_2C、屈氏体、M_7C_3、M_(23)C_6、M_6C、M_(12)C等碳化物。

White gold or yellow gold, platinum or stainless steel, even tungsten carbide.

白金或黄金，白金或不锈钢，甚至碳化钨。

Both of the twinning and epitaxial growth are important mechanisms for precipitation of titanium carbide in the TSCR steels.

总之，在钢中先行析出的Ti2CS和TiC粒子都可能成为新生成TiC的非自发形核地点，孪生和外延生长是TiC沉淀的两种重要机制

As an application,machining of 45# steel at 200 HB hardness using uncoated carbide tooling was investigated.

日益增长的时间、设备、材料和人力成本的消耗促使人们寻找更通用、更有效的研究方法。

The effect of solution and tempering temperature on the Charpy V impact energy AKV and HRC of ultra-high strength steel 23Co14Ni12Cr3Mo was studied, impact fracture surfaces were observed by SEM,and the undissolved carbide was analyzed by TEM.

研究了不同固溶及回火温度对高Co-Ni超高强度钢23Co14Ni12Cr3Mo的Charpy V型缺口试样冲击功AKV和硬度HRC的影响，并用扫描电镜观察分析不同处理状态下的冲击断口形貌，用透射电镜对未溶碳化物进行了分析。

Theexperimental results show that the performance ofthe dies can be remarkably raised through homogenizing original microstructure,controlling austenitizing and tempering process,and coordinating therelationship among undissolved carbide,...

结果表明，通过调整原始组织，严格控制奥氏体化条件及回火工艺，合理利用第二相、基体成分和残留奥氏体的关系，可显著提高强韧性和耐磨性，使冲模寿命比常规工艺处理提高10倍以上。

On the basis of examination of the wear behavior and worn surface morphology of the coatings after abrasive wear and erosion wear respectively, and the enhancing mechanisms of interlamellar bonding caused by unmelted carbide particles during deposition, the effects of the microstructure on its performance are discussed.

其次，在分析研究了涂层磨粒磨损和冲蚀磨损失效形貌以及未熔化碳化物颗粒对涂层层间结合强化机理的基础上，探讨了磨损机制、磨损模型的建立及涂层结构对磨损性能的影响规律。

In order to obtain adequate contrast between the worn and unworn tool regions, the intensity and angle of illumination of carbide insert were adjusted to accentuate the tool region of interest.

在为了获得足够的对比磨损和unworn工具地区，强度和角度的照明硬质合金插入进行了调整，以加剧的工具，地区的利益。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新