查询词典 cam press

A study on the CAD/CAM system assembler of the intelligent development platform of press dies CAD/CAM system

在分析传统的冲模 CAD系统体系结构的基础上，提出一种冲模 CAD系统的层次式体系结构及其开发平台的体系结构。

If practical, cam pierce stations should be designed to facilitate punch removal for in press maintenance.

如果可行，在凸轮冲孔工序中冲头应设计成便于移出，从而方便在冲床中维修。

Wear of the cam requirements apertognathia welding and replacement parts, disability and in disturbthe, avoid regulation disorder after a series of technology failures, at the same time according to the operating instructions for motorised offset press relations table may require adjustments to the data sheet transfer very lucky to have teeth, drum, delivery of dental clishion three parts in informention begnawing paper delivery must be adjusted in line with a sheet transfer very lucky to have teeth, drum, delivery time dental clishion Zhang arterious, Mr.

磨损的不开牙凹轮请求焊补和调换陈的配件，呈现漏洞，不给乱不静，制止调度井然后带来一系列工艺障碍，同时给根据胶印机搁置仿单的机不静干系外洋所请求的数据举行公道调不静，递纸牙、滚筒不小牙、收纸牙垫不一不小局部在咬纸传达时矮矮务必调不静分歧，递纸牙、滚筒不小牙、收纸牙垫弛不开工夫、弛不开巨细务必分歧，移交不确到位，都是在摈斥咬口纸边咬破障碍时调不静历程洋不该出格夺目的几个题目。

At least two spring legs extend from at least two spring coils and press against a cam on either side of the hinge knuckle.

至少两个弹簧支腿从至少两个簧圈伸出并且压靠在凸轮于铰链关节的任何一侧上。

Which is set up in the beginning of 1980,and developed with BasicA programming language based at the platform of DOS, the CAD/CAM System of Cold Press Dies is the outstanding CAD/CAM software that is proper to those small and medium-sized enterprises. But with the rapidly developing in the hardware and software of computer industry, it is forced to be faced to the being reformed or sifted out.

建立于80年代初期、在DOS平台上应用BasicA语言开发的冲裁模CAD/CAM系统是一个适用于中小企业使用的相当优秀的模具设计制造应用软件，但是随着计算机行业软件和硬件的迅速发展，使其面临着被改造或是退出历史舞台的命运。

Some factories although regreased system, but does not give effect to the delivery of spare parts, out of the oil killed breakdown; some factory adjacent to the mill of cam offset press under a pile of iron powder; no one in craft or oil caused by imperfect, and so on, but also equipment failure due to a missing check.

有的工场虽有加油轨制，但不落实到人，不入了机件断油咬活障碍；有的厂胶印机的凸轮旁磨下一堆铁粉也无人惯；罩壳边的油惯断裂或输油不到位等变不败的摆设障碍，也是由于充足查抄而变不败的。

Some factories although regreased system, but does not give effect to the delivery of spare parts, out of the oil killed breakdown; some factory adjacent to the mill of cam offset press under a pile of iron powder; no one in craft or oil caused by imperfect, and so on, but also equipment failure due to a missing check.

有的工场虽有增油轨制，但不落实到人，不入了机件断油咬活障碍；有的厂胶印机的凸轮旁磨下一堆铁粉也无人惯；罩壳边的油惯断裂或输油不到位等变不败的摆设障碍，也是由于充足查抄而变不败的。

Axotomized, turn the paper of the cam disconnect switch on the side of the circuit, forcing 3XK press paper cutter and a loss of power, but the operators have not yet had enough time to release the button, turn the paper cutting of the cam over the limit switch 3XK, 4J and 1 c was electric pick-up, gnashing paper cutter does not reset, in this case, a rotating cam on the other side lost your limit switch XM, intermediate relay 5J load-disconnected.

纸张切断后，转动的凸轮一侧断开行程开关3XK的回路，迫使压纸和切纸断电，但是操作者还未来得及松开切纸按钮，转动的凸轮滑过行程开关3XK后，4J和1C仍得电吸合，造成切纸刀不复位，这时，转动的凸轮另一侧断开了行程开关XK，中间继电器5J失电断开。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了