查询词典 calculations based on wishful thinking

There are four findings: 1 metaphor plays a more important role than metonymy in the extension of word meaning; 2 there are two important ways of thinking in the extension of word meaning: metonymical thinking based on contiguity and metaphorical thinking based on similarity.

研究发现：(1)隐喻在词义延伸中发挥的作用大于转喻；(2)在词义延伸中有两种思维结构： 1是以邻近性关系为基础的&部分代整体&的转喻思维结构；另1个是以事物相似性为基础的隐喻性联想思维结构。

There are four findings: 1 Metaphor plays a more important role than metonymy in the extension of word meaning; 2 There are two important ways of thinking in the extension of word meaning: metonymical thinking based on contiguity and metaphorical thinking based on similarity.

研究发现：(1)隐喻在词义延伸中发挥的作用大于转喻；(2)在词义延伸中有两种思维结构：一是以邻近性关系为基础的&部分代整体&的转喻思维结构；另一个是以事物相似性为基础的隐喻性联想思维结构。

In the numerical calculations,the unknown density of dislocation is approximated with the product of fundamental function and Chebyshev polynomials.The calculations show the present method yields rapidly converging and high accurate numerical results.

在数值求解这组奇异积分方程中未知位错分布密度近似为基本密度函数与Chebyshev多项式之积，计算表明，本文方法的数值结果不但收效快而且精度高。

On the basis of the hydraulic and kinematics calculations about revolving water decanter ,dynamics calculations were made in this paper.

在对旋转式滗水器进行了水力学和运动学计算的基础上，对旋转式滗水器进行了动力学计算，给出了其动力学计算公式，与水力学和运动学计算公式一起，共同给出了旋转式滗水器完整的设计计算公式。

The metric system for spur-gear calculations involves more than changing inches to millimeters .the basis for calculations in the American inch system is diametral pitch ,which is the number of teeth divided by the pitch-cirle diameter .In the metric-circle diameter by the number of teeth .

公制为spur-gear计算多变化，依据英寸到毫米的计算系统在美国英寸直径的球场，这是数量除以pitch-cirle直径的牙齿。metric-circle直径的牙齿。

In addition ,the thesis deals with amount of components devices and calculations ,including :(1) Choice of the main shaft and disposal of transmission , by doing so to ensure the accuracy of components machining in process when the main shaft rotating;(2)The device and check of the transmission shaft ,so it can assure the rigidity of the shaft is allowable ;(3) Gear device and calculations ,check the performance in the strength and rigidity of it ;headstock is a very important part in this thesis ,the design of it here not only ensures the rationality 、equipoise and stability of the motion of the slipway ,but also satisfies the requirements of different work environment .

液压装置的设计液压滑台、定位夹紧装置均为液压控制。并采用了许多液压控制阀，保证了运动的平衡性，循环性和精确性。另外，本文还涉及到大量的设计和计算，包括：（1）、主轴的选择和传动布置，以保证加工过程中被加工零件的精度；（2）、传动轴的设计和校核，以保证轴的刚度；（3）、齿轮的设计、计算，对齿轮的强度和刚度进行校核；多轴箱部分是本次设计的重要环节，本次设计中它的设计既要保证工作台的运动的合理、平衡和准确，又要满足工作要求。

Imitative calculations of the two portal-frame structures are carried out by utilizing the program, and calculations are in good agreement with experimental results.

运用本文程序对两榀门架结构进行了模拟计算，其计算值与试验结果吻合良好。

Three of them had right breast cancer and remainder had left breast cancer. For each patient, three-dimensional calculations were performed using full set Computer Tomography-slices. All calculations were done using 6MV-photon. The dose distribution of planning target volumes and critical organ were analyzed. Result: Both 3D and FIF technique provided acceptable planning target volumes coverage with 90% of the PTV receiving 100% of the prescribed dose in all cases.

本研究收集六位乳癌病人，其中包含三位左侧乳癌和三位右侧乳癌，每位病人都接受电脑断层摄影治疗规划，分别以3D和FIF两种技术做治疗计划，分析并比较其计划治疗体积和重要器官的剂量分布。

The accuracy of further calculations of the nonharmonic constants, frequency distribution of tidal level and high tidal level with the multiplier 2 hours are all dependent on the results of the harmonic constants derived above. Calculations of the nonharmonic constants will be different if the type of the harbor changes.

调和常数是否稳定决定了进一步计算的非调和常数、潮位频率分布和2小时乘高潮位频率分布的可靠性。

Establishing a geometric model of pump shaft with Three-dimensional modeling software and considering force condition to determine the boundary Conditions, after a reasonable simplification, then the modeling is inputted for ANSYS strength analysis combined with the traditional strength theoretical calculations of the shaft to get the result of stress and strain calculations and static stress and strain diagram.

应用三维造型软件建立了泵轴的几何模型，经过合理的简化，分析受力情况确定边界条件，在ANSYS软件中进行分析，结合传统的强度理论计算对泵轴的强度进行了计算和求解，得到了应力和应变的计算结果。

More direct, directer ; most direct, directest

径直的，笔直的

Do you know how to use a chain saw?

你知道如何使用链锯吗？