查询词典 calculating automaton

From this viewpoint, we fulfilled to control the step-size with the curvature of integral curve. The step-size is smaller in calculating these points that the value of the curvature is bigger and the step-size is bigger in calculating these points that the value of the curvature is smaller, which is rather reasonable choice and is also a creative point in this paper.

从这个想法出发，在文中实现了以积分曲线的曲率控制步长大小的作法，在曲率大的点步长小，而在曲率小的点步长大，这是非常合理的选择，也是本文的一个创新点。

Note that regularized problems are usually defined in an infinite setting and have to be discTetized for an implementation and there have been many comparatively adult methods of calculating singular system. Therefore, there is no need to avoid the calculation of singular system in inverse problems calculating of numeric value. Here TSVD Regularization Method is very simple and quite effective one.

考虑到反问题的数值计算需要将问题离散化，化为有限维的问题来进行处理，而对于有限维算子的奇异系的计算已经有了相当成熟的各种算法，因此在反问题的数值计算中没有必要避开奇异系的计算，此时TSVD正则化方法是十分简单并相当有效的正则化方法。

According to the arrange characteristic of irradiation source on the palling plate this paper deduces the equation calculating dose field The problem in calculating dose field of irradiator is solved with computer program The calculation values are in accordance with the measurement values .

自编程序解决了栅板源剂量场的计算问题，同时将计算值与实测值进行了比较，两者符合得很好。

It takes the function made up of Legendre orthogonal polynomial as displacement function, and use Galerkin method to solve this function. The methods calculating formulas is very simple, so the method can avoid the great calculating difficulty of traditional simplified methods.

正交多项式伽辽金法选取由勒让德正交多项式组成的函数作为位移函数，利用伽辽金法进行求解，计算公式简单，避免了一般简化计算方法由于计算公式的复杂所带来的计算困难。

Recurrent formulas for calculating the coefficients of the Legendre polynomial and the expressions for calculating the sedimentation coefficient are deduced analytically.

为了研究多分散低Péclet数沉降问题，我们先以Legendre多项式展开法得到了计算对分布函数的普遍递推式，以及由Legendre多项式的系数表示的沉降积分。

So, the approximate calculating formula of parabola and the length of ellipse arc is developed by the method of finding experience formula from point of view of simplifying the calculating process and getting certain accura...

本文从既能简化计算又能达到一定精度的设想，通过找经验公式的方法给出了计算机抛物线及椭圆弧长的近似公式，并给出了常用区间上计算抛物线和椭圆弧长的一次式和二次式。

The results are the following: When calculating the motion mass, it is better to use idler's equivalent mass instead of the rotating part mass and serial idler's rotating inertias and equivalent mass are calculated. The accurate analysis result for the deflection curve length of the belt shows: The error calculated by the approximate parabola length is lower than 10〓. Thus the approximate method is accurate enough for calculation. The relations between the running resistances coefficient and the belt velocity are studied by experiment, which are the bases for calculating the linear coefficient values between them.

得出：在计算参与运动质量时对托辊应采用托辊的等效质量而不是目前采用的托辊旋转部分质量，并计算出了系列的托辊转动惯量和等效质量；对输送带的挠曲线长度进行了精确的分析，结果表明：采用近似的抛物线长度计算方法其误差在10〓以下，因而得到在计算输送带挠曲线长度时采用近似的抛物线具有足够的精度；对输送机运行阻力系数与带速间的关系进行的实验研究，得出阻力系数与带速线性关糸的系数值。

The author presented the formulas used for calculating the lengths of rod parts of steel frame structure lightning conductor with different heights and sectional lengths,and explained detailed calculating methods combined with actual example.

根据钢筋构架式避雷针的不同高度和节长，分析推导出计算各杆件长度的实用公式，并以实例说明具体计算方法，为设计计算提供捷径。

The design and drilling methods include selecting a formation to be drilled, calculating a desired DOC and the strength of the formation, and calculating a height or thickness of a bearing element that may limit the DOC and the unit force applied to the formation.

设计和钻井方法包括选择待钻的地层、计算期望的DOC和地层强度和计算可限制DOC和施加到地层的单位力的支承元件的高度或厚度。

A calculating method to determine the clearance size of the rudder face along the extension direction of the swept-back wing for airplane is presented, which can be used for calculating the clearance size of the rudder face at limiting deflection angle, and point out that several parameters for determining the caearance is essential .

本文针对某型无人机翼面、舵面设计，首先导出了一种确定后掠翼舵面展向缝隙尺寸的计算方法，使用该方法能够定量地计算舵面在极限偏转角下缝隙的尺寸，并指出决定舵面缝隙大小几个主要参数，为舵面缝隙设计提供了可靠依据。

The dissecting of samples in group2 were difficult. The root of pulmonary artery and ascending aorta failed to be unfolded because fibrous tissue was tough, right and left fibrous trigone were too firm to be solved by hand. Cardiac muscle fibers couldn't be stripped along myofibrillar trajectory since they were prone to break because of their friability.

组2的心脏解剖困难，表现为纤维组织坚韧，游离肺动脉非常困难；徒手无法松解左、右纤维三角，肺动脉和主动脉根部的游离非常困难；心肌纤维坚硬、质脆，解剖时容易断离成碎块，无法沿纤维走行方向剥离。

We have battled against the odds in a province that has become increasingly violent.

我们对在一个争夺日益激烈省的可能性。