查询词典 calculate

The commons among those methods is that all of them calculate the mean vector and the covariance matrix of sample then calculate other variables by using them.

这些方法有个共同的地方就是都会计算样本的均值向量和协方差矩阵，并在这两者的基础上计算其他统计量。

To calculate the interactive parameters of DBP and mesitylene, o-ethyl-methylbenzene and 1,2,4-trimethylbenzene, the method of chromatography is used in the paper to measure γ~∞, along with the method of single parameter, to calculate the model parameters of the model of Wilson.

采用色谱法测定C_9各组分在邻苯二甲酸二丁酯中的无限稀释活度系数，结合单参数法模拟计算Wilson模型参数。

To calculate self and mutual inductance of coreless transformer in printed circuit board, The author offered a new method to calculate based on Neumann equation as well as testing process and circuit.

为了计算印制版空芯变压器的自感和互感，提出一个以纽曼公式为基础的新的计算方法，并给出了测试方法和测试电路。

Point reactor dynamic equation is a simple equation that not considered reactor space factor, it was used to calculate the dynamic proliferation of reactors because there is no space variable , otherwise it can be used to calculate coupled with the thermal feedback to get the number of neutron density changes situation.

点堆动力学方程是不考虑反应堆空间特性的简单方程，由于没有空间变量所以它通常被用来计算反应堆的动态增殖特性，而且可以用来与热工耦合计算有反馈的中子数密度变化情况。

A new analytical method, was presented to calculate the diameter and height of spray dryer in order to improve the tedious process of diagram integral method which must read the nomogram repeatedly and overcome the difficulty of diagram integral method which could not be programmed to calculate.

为了改进图解积分法要反复查列线图的繁琐过程及克服该法不能编程计算的困难，提出了计算喷雾干燥塔直径和高度的一种新方法——解析法。

During the optimization, we should calculate the oilcan cubage of the start station, output oil deposit and the final station according to different transportation circle, and calculate the oil mixture sum and the management fee according to transporting sequence, then finally decide the optimum transportation circle and the cubage of oilcans.

优化批次、罐容时应根据不同批次分别计算首站罐容、分输油库和末站罐容，并根据输送顺序计算混油量以及混油处理的各项费用，最终确定管道的最优批次和罐容配置。

Calculate way 1: Inside it the parameters number have already known, the unknown X of the square equations , can pass to push the estimate of with following calculate way: Among them α=0.95 ～ 0.99 for forgetting the factor, mean the oushifan number, block diag to mean to divide an opposite angles matrix .

算法1：当中参数已知时，方程的未知数X，可用如下算法递推估计：其中α=0.95～0.99为遗忘因子，表示欧氏范数，block diag 表示分块对角阵。

First, we calculate out the zero point in a simple numeral method, then we get the phase according to the fact that the symbol of phase changed is opposite in the positive-slope and the negative-slope of triangle wave. This method has the following characteristics: easy to calculate, simple to realize and high precision.

首先用简单的数值方法较准确的计算出零点时刻；进而根据三角波扫频时正程和逆程相位变化符号相反的特性，巧妙的完成了相位计算，该方法具有计算简单、实现方便、准确度高等特点。

The formula was established about calculating design parameters and technological parameters of ideal strip and bent strip in the period of forming. The thesis presented how to calculate the deformed area length and contact are radius of contact deforming between two elastic bodies on condition of the friction. The calculating formula of pinch force about plate-strip pinch mill was given and the results were analyzed that friction coefficient and radius of pinch rolls are very important for determining pinch force. Moreover, the rule of deforming and stress distribution of different 〓 ratio were gained on condition that the deforming was considered to be non-uniform distribution in the gap. The differential equations were got that calculate the displacements of large deflection of elastic cantilever rectangle plate with fixed end and the formula of the Finite Strip Method was conducted to study the regularity of mid-plane displacements, deformation and stresses for elastic-plastic large deflection bend of cantilever parallelogram plate with fixed or slidable end by integrating Prandtl-Reuss equation.

建立了一套完整的设计参数计算公式和在成型过程中理想带钢或具有月牙弯带钢的工艺参数的调整公式；在考虑摩擦力的条件下，对两弹性体接触变形过程中的接触变形区长度和接触弧半径用位移解法进行了研究，推导了板带递送机的递送力计算公式，从而得知在递送机设计过程中，应选择适当摩擦系数和辊身直径；另外，还从辊缝内带钢实际变形出发，分析了对于不同的〓值，带钢的变形规律及应力分布状况；建立了固定端悬臂矩形板弹性大挠度弯曲变形的控制方程，并且在对Prandtl-Reuss方程的积分处理的基础上，导出了固定端和滑动端悬臂平行四边形薄板的弹塑性大挠度的中面伸展位移、变形和应力的有限条元法公式，编写了Fortran语言计算程序，在各种参数条件下，对螺旋焊管成型过程变形规律进行了全面的分析研究，从而为螺旋焊管的生产和进一步的改进提供了理论依据。

In the numerical computation, a two-dimensional numerical method integrating finite element method and difference method was employed, where the finite element method is used to calculate the magnetic field of the permanent magnetic guideway and the difference method is used to calculate the induced current in the superconductor, then the levitation force and the lateral force were calculated by Lorentz formula.

在数值计算部分，实现了一种集有限元法与差分法为一体的数值计算方法。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了