查询词典 by-product circuit

In this paper the reason of rapid increase of single phase short circuit current in 500 kV substation is analyzed. Through the calculation it is proved that neutral grounding by small reactance is an effective measure to reduce the single phase short circuit current, and the calculation method of the zero\|sequence reactance after autotransformer neutral grounding by small reactance being applied is expounded.

文中研究了500kV变电站单相短路电流急剧增长的原因，计算了变压器中性点经小电抗接地对限制单相短路电流的作用，论证了经小电抗接地是限制单相短路电流的有效措施之一，并阐述了500kV自耦变压器中性点经小电抗接地后，其等值零序电抗的计算方法，可供工程参考。

This paper gives out the principles and improving schemes of transformer discharge equipment and resonance booster discharge equipment. By detecting the current in the main circuit, the gap's breaking-down can be identified, and the single chip micro-computer will send out corresponding control signal to make the IGBTs to switch off or cut off the input voltage, by this mean, we can make sure that every time of the experiment, the sample will discharge only once. The paper also introduces the principle of the protection circuit. At last, the experimental waveforms were listed, which prove the feasibility of the high voltage discharge fast switch-off device.

该文给出了变压器和谐振升压器2种高压放电试验装置的原理以及改进方案，通过检测主回路电流大小判断间隙是否被击穿，由单片机发出相应控制信号，采用IGBT等开关器件控制试验电压的通断，保证了试品每次试验只进行一次放电，介绍了保护电路的原理，给出了试验波形，证明了此高压放电速断装置的可行性。

Comparing the synchronous rectifier to normal circuit by calculating the efficiency indicates that forestay is much better on efficiency and thermal performance. A simple circuit with good consistency, high efficiency, high reliability and low cost is presented in this paper. The feasibility is proved by emulating with computer.

通过分析已有的集中解决隔离型变换器输出带预偏置电压启动的解决方案，提出了一种全新的一致性好、成本低、效率高、简单和可靠性高的解决隔离变换器输出有预偏置电压的启动问题的电路，通过仿真验证了其可行性。

On the basis of instantaneous forced analysis to short circuit of power transformer and numerical value calculation using low voltage impulse analysis, the paper presents the essentiality of winding distortion after short circuit of power transformer. By contrasting the three main ways of the world such as low-voltage impulse、 short circuit impedance analysis and frequency response analysis , FRA is adopted for distortion testing. Then we design a new testing instrument of transformer winding distortion—testing system of transformer winding distortion.

本文首先在对电力变压器短路时的瞬时受力分析及所受电磁力的有限元法的数值计算的基础上，论证了电力变压器短路以后进行绕组变形测试的必要性；然后通过比较的方法对目前国内外主要使用的三种方法：低压脉冲法、短路阻抗法和频率响应法，进行了一一对比，并根据对比结果，确定在本课题中使用频响法；最后在理论研究的基础上，设计出了一种新型的变压器绕组变形测试仪——电力变压器绕组变形测试系统。

In retiming registers are added at some points in a circuit and removed from others in such a way that the functional behavior of the circuit as a whole is preserved. By retimng we can optimize the speed, area or power of the circuit.

重定时在保证功能不变的前提下，通过移动时序元件的位置和改变时序元件的个数来优化同步时序电路的速度、面积和功耗。

The relations between the simulation circuit parameters and the linear motor parameters were achieved by analyzing the equivalent circuit of the linear motor and the simulation circuit of piston displacement self-sensor.

通过分析直线压缩机的直线电机的等效电路和活塞位移自传感器的模拟电路，得出了模拟电路参数与直线电机参数之间的关系。

To presents the methods of designing and making circuit board for experimental teaching by computer, laser printer and heating roller, which are the methods of designing and making printed circuit board on one-side copper plate and the circuit drawing, on insulated epoxyresin base.

介绍了利用计算机、激光打印机和制板机设计制作实验教学电路板的方法。即在单面覆铜板的铜面设计制作印制电路板，在绝缘玻纤环氧树脂基面设计制作电路原理图。

And this paper introduced the principium, design ideal and approach of waveform presetting of waveform controlling at will The function of relevant hardware circuit controlling was design in this paper uses litter content RLC surge circuit in simulating the current signal of energy storage welding, and took it as Ug to control the inverter cap energy storage spot welding machine. It realized HFPEC resistance spot welding with hardware circuit and got the effect as good as the system controlled by industrial computer and realized the customization and the low cost of welding machine.

本文所设计的相应硬件控制功能，采用小容量RLC 放电回路来模拟输出储能焊过程的电流波形，由此作为电流给定信号直接控制逆变式电容储能点焊电源，实现了完全由硬件电路构成的高频脉冲电阻点焊，能够获得焊接设备的专用化和低成本化的结果，并且可以得到与工控机控制系统相当的焊接效果。

The article shows a new kind of power controller of micro-satellite. The controller is composed of charge control. Discharge control, shunt control and the equilibration circuit. The output voltage is stabilized by an automatic circuit controlled by the PWM signal, which is produced by comparing the sampling value of the output voltage with the reference voltage. The application indicates that the system which insured the safety property of Li-ion battery series runs stably as well as satisfied the need of the load no matter in what situation.

在我国航天用锂离子电池组控制电路研究相对落后的背景下，设计一了种新型的微小卫星电源控制器；该电源控制器包括充电、放电、分流和均衡保护部分，充电、放电、分流部分通过将母线电压的采样值与预设参考值比较产生PWM信号对制电路进行自动调节，均衡通过采样和处理器计算比较实现；实验结果表明，该控制器工作稳定，确保了锂离子电池组工作安全的同时，很好地满足了各种情况下母线负载的需求。

Overall system is constituted by temperature sensor, signal gathering electric circuit, keyboard, display circuit, E2PROM reading-writing electric circuit.

本设计采用AT89S51单片机的两个I/O口扩展I2C总线，整个系统由温度传感器，信号采集电路、键盘、显示电路、E2PROM读写电路构成。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。