查询词典 by error

The magnitude of coning error which is affected by the fixing error , gyro' s quantizing error and frequency band , and so on is deduced based on the analysis of kinematic mechanism of coning error generation.

本文在分析了圆锥误差的运动学机理的基础上推导了由于安装误差、陀螺量化误差、陀螺频带选取等因素影响下圆锥误差的大小。

Because the weights are determined by the correlation of code sequence and estimation error of channels, which can be nearly determined by system load factor, we determine the sub-optimum weights by system load factor through simulations, and substitute the hard-decision symbol function by soft-decision hyperbolic tangent function to decrease the risk of error decision.

由于加权因子取决于前级符号估计的可靠性。也就是取决于扩频码互相关系数与信道估计精度，在随机扩频系统中，估计精度可近似由系统负荷决定，因此可根据系统负荷决定加权因子，以很小的性能降低代价换取计算量的极大降低。同时，为进一步降低误判风险，使用带有斜率控制因子的双曲正切函数代替常规的符号函数。

By dealing with regularization error,sample error and hypothesis error,we estimate the total error in terms of properties of the kernel,the input space,the marginal distribution,and the regression function of the regression problem.

样本相关的假设空间将为误差分析带来一项额外的假设误差，这一点与通常情况下样本无关的假设空间有本质的区别。

We gain the distributing instance as a whole by the spatial analyse of the daily、 mensal and annual precipitation.Then, we adopt mean error、 mean absolute error、 mean relative error、 and the root mean squared interpolation error and the correlative coefficient as the determinant standard of interpolation effect. The results show that the mensal precipitation effect of SIA is the best, and the daily precipitation effect is worse reversely.

然后，对年降水量、月降水量以及日降水量的SIA结果采用平均误差、平均绝对误差、平均相对误差、插值平均误差平方和的平方根误差以及相关系数作为判定插值效果的标准，并得到以下结果：月降水量的SIA效果最好，日降水的相对较差。

The author made an analysis of the ratchet gearing used let-off mechanism in the K251 type loom and of the effect to loomage, and came to the conclusion that is: 1. The long length of the loom cause bigger LO, which reduce weaving defects caused by let-off error. 2. At the same status of the loom, the possibility of appearing weaving defects is relative to the characteristic of the loomage, namely, if the stiffness coefficient of the loomage and organzine has lesser difference, the possibility of appearing weaving defects will be lesser, contrarily will bebiggish. 3. The displacement error AL affects the value of the weavingdefects directly, besides wind error, it is a effective method to reduce let-off error.

通过对K251丝织机棘轮送经机构及其对织物影响的分析，得出以下结论：1、丝织机的长机身使Lo较大，有效地降低了由送经误差造成档疵的可能。2、在织机状况相同的情况下，档疵出现的可能性与织物的特性有关，即织物与经丝的刚性系数相差较小的，档疵出现的可能较小，反之较大。3、织口位移误差△L，对档疵有着直接的关系，除了卷取误差，减少送经误差是减少档疵出现的有效的方法。

The error is described by weighted average variance-covariance of root mean square error in curve normal direction, and error in the direction with maximum error respectively.

曲线上任意点的误差由端点及距离误差传播导出的误差之加权平均值的协方差表示。

However, it is impossible to foresee the decoder state within the round-trip delay time. Consequently, to prevent such possible error effects, we further enhance SBET by ROPE. The encoder will recursively keep estimating the expected decoder pixel distortion. The distortion of frame reconstruction at the decoding side includes the quantization error, propagation error, and concealment error.

然而，在往复延迟时间内的情况则是无法预知的，因此为防范可能的错误蔓延，我们提出将递回式最佳像素预估法与其进一步结合应用，让编码端用递回的方式计算出解码端像素失真量的期望值，此失真量会包含量化失真、错误蔓延的错误和错误隐藏所带来的错误。

In this paper, based on the fundamental principle of the three-point method roundness error separation technique, the separation of cylindricity error factors and the reconstruction of the measured cylinder profile was intensively studied, and the methods of evaluating the cylindricity form error were discussed. Furthermore, the separation and reconstruction methods of the cylindricity error proposed in this paper were examined by the experiment.

本文采用三点法圆度误差分离技术的基本原理，重点研究圆柱度误差要素的分离和被测圆柱体形貌重构问题，探讨圆柱度形状误差的评定方法，并对本文所提的圆柱度误差分离及重构方法进行实验验证。

To study the calibration accuracy of stuctured light system based on cross-ratio invariant,measuring error and light-plane calibration error of system are analyzed,and an error propagation model is established by employing theories of error and matrix disturbance.

针对基于交比不变原理的结构光光平面标定方法，利用误差分析理论和矩阵扰动原理分别对系统的测量误差和光平面标定误差进行分析，提出了结构光测量系统的误差传递模型。

Based on analyzing performance of gear machining system and mechanism of machining error, the description method of machining error was presented for gear machine. According to the performance-driven design concept and generalized multi-body certainty theory, driven by gear machining error, machining error fine model and system integrated design method of CNC gear shaper was studied.

本文在分析齿轮加工机床的系统性能和加工误差产生机理的基础上，提出了加工误差描述方法；以&性能驱动设计&为基本理念，以齿轮加工误差为驱动，以广义确定性多体系统为理论基础，研究了数控插齿机加工误差精细分析和系统集成设计方法。

I am accused of being overreligious," she said in her quiet, frank manner,"but that does not prevent me thinking the children very cruel who obstinately commit such suicide.""

客人们在卡罗利娜·埃凯家里，举止就文雅一些，因为卡罗利娜的母亲治家很严厉。

Designed by French fashion house Herm è s, this elegant uniform was manufactured in our home, Hong Kong, and was the first without a hat.

由著名品牌 Herm è s 设计，这件高贵的制服是香港本土制造，是我们第一套不配帽子的制服。