查询词典 button switch

Step one: press Win + Pause / Break key combination to open "System Properties", switch to the "Advanced" tab, click the "Environment Variables" button, in which the "system variables" column, click on the "new" button in the "variable name" inside input "Devmgr_show_Nonpresent_Devices", in "Variable Value" enter "1", three "OK" after the withdrawal from the "System Properties" window

第一步：按下Win+Pause/Break组合键打开"系统属性"，切换到"高级"选项卡，点击"环境变量"按钮，在其中的"系统变量"栏中，点击"新建"按钮，在"变量名"里面输入" Devmgr_show_Nonpresent_Devices"，在"变量值"输入"1"，三次"确定"后退出"系统属性"窗口

Self-protect, press the seset button quickly (nit more than 0.1 second), turn on the illumining switch.if the led lighting normally, the system resume normal. if the led light blinks, turn the swith to off, and then press the seset button .if the led light turns dark, the module need to be charged.

模块自保护，可短按顶部的复位按钮（按下时间不能超过0.1秒），打开照明开关，如LED正常发光，即功能己恢复正常，如照明LED不能正常跟光，请先顶部开关拔至&OFF&，再短按复位按钮，如，LED光明显变暗，表示本电能模块需补充电量了。

This is the OpenGL texture rotary switch realization example, through the switch button to switch to achieve texture.

详细说明：这是OpenGL实现纹理旋转切换的例子，通过按键的切换实现纹理切换。

Axotomized, turn the paper of the cam disconnect switch on the side of the circuit, forcing 3XK press paper cutter and a loss of power, but the operators have not yet had enough time to release the button, turn the paper cutting of the cam over the limit switch 3XK, 4J and 1 c was electric pick-up, gnashing paper cutter does not reset, in this case, a rotating cam on the other side lost your limit switch XM, intermediate relay 5J load-disconnected.

纸张切断后，转动的凸轮一侧断开行程开关3XK的回路，迫使压纸和切纸断电，但是操作者还未来得及松开切纸按钮，转动的凸轮滑过行程开关3XK后，4J和1C仍得电吸合，造成切纸刀不复位，这时，转动的凸轮另一侧断开了行程开关XK，中间继电器5J失电断开。

This red light on top of button is the Show of ultrasonic launching.3:Training the dog: Function switch dial in the "OFF" position, With the Ultrasonic generator toward dog, Pressed the button "TRAINING CALL" at Back, which will be issuing 23KHz ultrasonic of 100dB strong, with gestures and password, your dog can be trained to do some specific action.

此按键上方的红灯是超声波发射指示灯。3。训狗：功能开关拨在&OFF&位置，超声波发射头对住狗狗，按动背面的&TRAININGCALL&按键，即会发出23KHz约100dB的超声波，配合手势和口令，可训练您的爱犬做一些特定的动作。

Note: flameproof push button box with four button, four indicators, two ammeters, one voltage meter and one switch

说明：隔爆型按钮箱，面板装有4只按钮，4只指示灯，2块电流表，1块电压表，1只开关。

The whole machine electricity uses the PLC programmable preface controller and adopt a proface touch to hold, operation convenient, dynamic state manifestation equipments operation and break down circumstance, change a machine, close switch, button the switch, knob switch, indicator all adopt import component.

整机电气用PLC可编程序控制器、采用proface触摸屏，操作方便，动态显示设备运转及故障情况，变频器、接近开关、按钮开关、旋钮开关、指示灯均采用进口元件。

This article has made statistic and analyses on many types of flameproof button and switches used in coalmine, such as travel switch, limit switch, pull switch,and so on.

就煤矿井下现用的隔爆按钮以及行程开关、限位开关、打点器、拉线开关、井口开关等进行了统计、分析，针对使用中出现的问题提出了改进措施。

Driver sets mode switch to "OFF", and pulls out master control key; waits for and until the indicator of "train reversal ready" flashes , presses "driverless reversal operation button" on the driver console, or else, leave the train and presses "driverless reversal operation button" on platform; train automatically drives to reversal tracks and backs to departure platform, car doors and platform screening doors are automatically opened, the driver moves into the driver cabin and inserts the key.

司机将模式开关设置为&OFF&位置，拔出主控钥匙；等待&列车折返准备好&指示灯点亮后，按压驾驶台上的&无人自动折返按钮&，或者离开列车，按压站台&无人折返按钮&；。列车自动运行到折返轨并回到发车站台，自动打开车门和站台屏蔽门，驾驶司机进入驾驶室，插入钥匙。

Lid landing gear box body is formed with the motor gearbox. When the furnace cover needs opening , simply press the button in the control box then the furnace cover will descend at a uniform speed .For the sake of safety ,two movements institutions tops trip switch are mounted in the carburizing EAF .When the furnace cover is ascending , the lower movements institutions tops trip switch will automatically cut off the seepage carbon EAF control cabinet main circuit power supply, forcing the heating elements stop working since the power is cut off, The upper switch is used to restrict the height of the movements axis ,it can prevent the movements pumped up too high to cause theelevating screw abscisicing from the gear box.

炉盖升降机构由电机齿轮箱组成，当需要开启炉盖时，只需按下控制箱上的按组，炉盖即以均速上升下降，为了安全起见，在渗碳电炉升降机构上装设有两个行程开关，当炉盖上升时，下边的行程开关自动切断渗碳电炉控制柜主回路电源，使加热元件断电停止工作，上边的行程开关则限制升降轴升起的高度，以防升降抽升起过高，升降丝杆脱出齿轮箱。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。