查询词典 butt joint

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

The mechanical effect of the crack initiation and propagation under a residual stress field is analyzed, and then the residual stress redistribution because of cracking in the welded residual stress field in a plate butt welded joint is successfully calculated by means of the elasto-plastic finite element method .

分析了在残余应力场中裂纹产生和扩展所引起的力学效应，并成功地运用弹塑性有限元方法计算了平板对接接头焊接残余应力场中裂纹扩展引起残余应力的变化。

To get a property comparison of GXHJ－ 1 sintered welding agent with SJ101 sintered welding agent, related tests were carried out, including deposited metal test, lab butt－ joint plate test, single－ welding stick operation test, double－ welding stick operation test as well as operation test with H08C welding stick, focusing differences of the two in terms of technological properties and weld seam impact toughness.

为了比较 GXHJ－ 1和 SJ101两种烧结焊剂的性能，分别从熔敷金属性能试验、实验室对接板试验、单丝焊生产、双丝焊生产等方面及在匹配 H08C焊丝的条件下进行了工艺性能和焊缝冲击韧性对比。

The properties of the flash butt welding joint achieved the level of the foreign experiment results. It can meet the requests of the correlation technology condition.

高锰钢辙叉与钢轨闪光对焊接头的抗拉强度达钢轨母材的60%左右；冲击韧性值也在钢轨母材冲击值的60%以上，其接头力学性能接近或达到了国外加过渡层闪光对焊接头力学性能的水平。

I concluded early in the company's products steel products joint electricity pressure welding slag, flash butt welding at the same time, developed a cone thread, cold extrusion reinforced mechanical joints.

我公司产品在总结早期产品钢筋接头用电渣压力焊、闪光对焊的同时，又开发研制了锥螺纹、冷挤压钢筋机械连接接头。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。