查询词典 braze

Using carbon, iron, silicon, ferrochromium, ferrotitanium and nickel powder as the raw ma terials, chromium carbide/Fe-based composite coatings with an even and smooth surface were prepared by vacuum reactive braze coating, which combined with a mild steel substrate by a metallurgical bonding.

以纯铁粉、硅粉、硼铁粉、铬铁粉、胶体石墨及镍粉为原料，通过真空反应钎涂在低碳钢基体上制备了碳化铬／铁基自熔合金复合涂层，涂层表面光滑、平整且与基体为冶金结合。应用扫描电子显微镜、能谱仪、X射线衍射仪及显微硬度计，研究了涂层的组织结构、成分分布和硬度分布。

Efforts to simplify the cladding process by substituting a glassless braze-HIP cycle for the glass-HIP diffusion bonding cycle were not successful due to the inability to insure 100% leak-tight brazed seams.

为了简化程序，以覆面的刹车glassless-Hip周期为玻璃胯扩散焊接周期没有成功，因为无法保证100%漏风雨焊缝。

Main process flow of aluminium heat exchange is as follows: dewinging→spare parts cleaning→core installation→braze welding→final argon-arc welding→ leak test→curb plate and accessory assemblage→lacquering→packaging.

铝换热器主要工艺流程是：冲翅→零部件清洗→装芯→钎焊→总成氩弧焊（总成装配→密封性检测→侧板及附件装配→喷漆→包装。

Under torch brazing condition, using brazing filler metals of Cu-based and Ag-based, a series of tests are investigated to braze Ti based cermets and 45 steel, the micrographic structure of joints and shearing test results are analyzed, they show that Ti based cermets has good brazability.

通过观察和分析钎焊接头的结合情况及剪切试验，表明 Ti基金属陶瓷具有较好的钎焊性；火焰钎焊条件下，以 H 6 2为钎料的接头的平均剪切强度为37MPa，以 BAg10 Cu Zn为钎料的接头的剪切强度达 114 MPa，以 BCu Zn Mn为钎料的接头的平均剪切强度为 4 9MP

Nickel-boron alloys form the basis of brazes used to join many nickel-base alloys,especially in aerospace.a eutecytic forms between nickel and nickel boride n and so a nickel boron braze can melt and flow without melting the nickel-base materials to be joined.

镍硼熔合依据镀黄铜过去常常加入许多镍基地合金的形式，特别是以航空航天。a eutecytic形式之间镍和镍硼化物n和镍硼如此镀黄铜可能熔化和流动，无需熔化将被加入的镍基地材料。

The faying surface of the samples were ground and then polished in 1.0 μm alumina and cleaned ultrasonically in acetone for 15 minutes before assembling the braze joint.

该发英表面的样本，然后在1.0微米抛光氧化铝和在丙酮超声清洗15分钟，然后组装钎联合。

It is suitable to be used as filling material for oxygen-acetylene gas welding and carbon arc welding, and also for manual braze welding. It is the ideal material for welding of copper alloy, copper, gray cast iron and hard alloy knife and etc.

HS221 JIS ZYCusN 适用于氧-乙炔气焊及碳弧焊时作为填充材料，也可用于钎焊，是铜合金、钢、灰铸铁及硬质合金刀具等焊接材料中较为理想的焊接材料。

The manufacture of copper core of automobile radiator includes coating tinned or bared copper cooling pipe; roasting assembled main core inside braze welding furnace at 230-280 deg.c for 30-60 sec; welding main sheet to cooling pipe via conventional process; and welding the copper lid opening for the water chamber with brazing agent without solder and welding filament.

一种铜质汽车散热器主芯的制造方法，其先将镀锡冷却管或裸铜冷却管外壁分别进行覆膜处理。将组装好的主芯主体置于铜钎焊炉内于230～280℃温度焙烧30～60秒。主片与冷却管间采用常规的方法焊合。还可以将组装好的主芯主体每排冷却管上摆放一根外表面涂有无钎料钎剂膜的锡焊丝，它们贴在冷却管与主片结合处。

From international development trend of copper radiator, braze welding copper automobile radiator has the characteristics such as high quality and low cost and will gradually replace the former soldering copper radiator.

但从国际上铜质散热器发展趋势看，由于硬钎焊铜质散热器具有质量好、成本低等特点将逐步替代原软钎焊铜质散热器，市场前景十分广阔。

Keywords reactive braze coating;chromium carbide;composite coating;Fe-based self-fluxing alloy

反应钎涂；碳化铬；复合涂层；铁基自熔合金

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。