查询词典 brake-van

If they could really out-brake the other, they would have made some overlap before the turn-in point, not after it.

如果他们真的可以比他人延迟刹车，那么他们早在进"入弯点"前就应该建立了"重叠"，而不是之后才建立。

So release the brake pedal gradually and try to make sure you have fully lifted from the pedal just before you turn-in.

所以在入弯前一定要逐渐释放刹车，并确认完全放开刹车。

But you don't want to lock up at all so for the moment don't even think about it - just concentrate on releasing the brake pedal smoothly as you reach the end of your braking zone (and the start of your turn-in point) and there shouldn't be too many problems.

当然我们根本不希望轮胎锁死了，所以要注意：在减速区末段平滑的释放刹车（或在减速区开始平滑的踩下刹车）。这样就不会有太大的问题。

Well that's because a rear brake bias can really help corner turn-in as the car is automatically trying to oversteer, and in the early stages of this 'oversteer under braking' it will normally point the nose of the car in the direction you want to turn.

这是因为偏后刹车比可以帮助入弯，赛车会自动发生轻微的转向过度，这能够使赛车指向你想要的方向。

The simple solution to this is to remember to release the brake pedal completely just before turn-in - as long as you have reduced your speed enough for the corner there shouldn't be any problems as you get back on throttle ready to drive through the upcoming corner.

简单的解决办法就是入弯前完全释放刹车，只要你减速的非常充分，再加些油门过弯就不会有问题。

Via checking, affirm Nanjing all directions 100 million can the company debugs an engineer to be in to pyroelectricity line of 8 total mix measures gold of one station 10KV in accusing what accept supervisory system partly to debug a process, did not check seriously equipment name, also did not get tutelar personnel to affirm, do sth without authorization has the operation dividing brake of breaker, in will moving by accident advocate change 3-10KV breaker is pulled open.

经查，确认南京四方亿能公司调试工程师在对热电一站10KV金8总调线路测控部分接入监控系统的调试过程中，没有认真核对设备名称，也没有得到监护人员确认，擅自进行断路器的分闸操作，误将运行中的主变3-10KV断路器拉开。

Styling / Convenience Engine Trim Black powder-coated with Wrinkle-Black treatment Exhaust System Chrome, staggered shorty duals Foot Supports and Controls Mid-mounted rider footpegs with brake and shift levers; standard passenger footpegs Handlebars Stainless steel, wide, dirt-track inspired Seat One-piece, two-up Sportster classic Instruments Electronic speedometer with odometer, time-of-day clock on odometer, dual resettable tripmeter, fuel gauge with low fuel warning light, low oil pressure indicator light, diagnostics readout, LED lights, tachometer Hazard Warning Integrated into turn signal controls Smart Security System Optional, next-generation hands-free security fob; operates based on proximity to vehicle

称呼/便利引擎修剪黑色粉末上漆与皱痕黑治疗排气系统镀铬物，摇摆的shorty 双倍脚支持和控制中间登上的车手footpegs 与闸和转移杠杆；标准乘客footpegs 把手不锈钢，宽，土轨道启发了位子单件， two-up Sportster 经典仪器电子车速表与测路器， time-of-day 时钟在测路器，双重resettable tripmeter，燃料测量仪以低燃料警告灯，低油压显示灯，诊断读出， LED 点燃，车头表危险警告集成轮信号控制聪明的保安系统任意，下一代没有雇工的安全fob；操作根据与车的接近度

If I had to do it again, I would have had left the haul bag on the ledge with Wes. Then I would pendulum across with both the main line and the haul bag line. I'd pull both tight and tie them off at the belay stance. Then Wes would put the haul bag on his back and Tyrolean down to me -- using one of his jumars reversed as a brake.

假如我得再做一次，我会把拖包及Wes放在那里，然后我摆荡横渡主线及拖拉线，再将他们从确保站立处拉上来，然后Wes把拖包放在背上再Tyrolean下到我这里，用他其中一个犹玛制动。

The engineering facilities service mainly take JIAOMEITE,DACROMET series spreading equipment as the leadership,it is good at development and production of special-purpose spreading equipment by spare parts for car,for example the automobile brake disc,braking,muffler,exhaust,oil pipe,U shape bolt,deep hole bolt and so on the special product special purpose equipment.

工程设备业务主要以焦美特、达克罗系列涂覆设备为主导，尤以汽车零部件专用涂覆设备的开发、生产见长，譬如汽车刹车盘、制动毂、消声器、排气管、油管、U形螺栓、深孔螺栓等特殊产品的专用设备。

In this article , instead of changing the ubiety among the parts of the original elevator , the author keeps on using the original structure. However, because of the differences of the transmission ratio and speed, the author enlarges the planet gear, solar gear , thickness of the inner circle ring as well as the enclasping radius of the enclasping brake through the mechanical design and calculation .

在设计过程没有改变原有的升降机零部件的位置关系，但由于，传动比以及传动速度的不同，所以，通过受力分析计算，加大了行星齿轮、中心齿轮、内齿圈的厚度；同时也加大了抱闸抱紧时的抱紧半径。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。