查询词典 brake valve

Diagraph spring pneumatic brake valve is widely used as control valve for tractor - trailer braking system.

膜片弹簧式气制动阀作为控制阀已广泛地应用于拖拉机挂车制动系统。

Caused by disc brake on the brake Wheel Cylinder could not return to places 4 possible: First, 5 foot brake valve exhaust port blocking, high-pressure gas instinct platoon atmosphere, caused by gas-liquid master cylinder of the spring could not return to place, resulting in the system move oil, brake disc brake Wheel Cylinder Piston top dead and could not return to places; second is to the disc brake master cylinder gas-liquid pipeline blockage, resulting in brake Cylinder piston can not return to place; third master cylinder of the gas-liquid Spring itself can not return to position, brake fluid under high pressure gas can not return Axial pump to gas-liquid master cylinder reservoir chamber, resulting in brake Cylinder piston can not return to places; Fourth Wheel Cylinder piston disc brake system, due to moving fluid dirty or rusty card dead and can not return to the piston position.

造成盘式制动器上的制动分泵不能回位有4种可能：一是脚制动阀5的排气口堵塞，高压气体本能排人大气，造成气液总泵的弹簧不能回位，导致制动油将盘式制动器的制动分泵活塞顶死而不能回位；二是气液总泵至盘式制动器的油管堵塞，造成制动分泵活塞不能回位；三是气液总泵的弹簧本身不能回位，制动液在高压气体作用下，不能回到气液总泵的储油室，从而造成制动分泵活塞不能回位；四是盘式制动器制动分泵活塞由于制动液太脏或活塞生锈卡死而不能回位。

A small four-wheel tractor air BALANCING VALVES brake valve tappet is made of plastic, and its diameter and length are often vulnerable to the effects of thermal expansion and contraction changes, resulting in air brake failure.

小四轮拖拉机的气制动阀挺杆是由塑料制成的，其外径、长度往往易受热胀冷缩的影响而改变，导致气制动阀失灵。

The performance of brake valve is connected with the security of automobile. It is very important to eliminate lacunas of inner subface.

制动阀的性能关系到汽车制动的安全性，对其内底面的缺陷必须及时予以剔除。

It intergrates researching, manufacturing and selling together and specialize in producing spare parts of various types of cars,such as air brake parts, clutch booster, spring brake chamber, brake valve, relay valve and so on.It is one of the most important manufacturer of brake parts at home.

它集研发、制造、销售于一体，专业制造各种车型的气制动元件、离合器助力器、弹簧制动缸、手控阀、刹车总泵、继动阀等系列产品，是目前国内汽车制动元件的重要生产基地之一。

On the basis of the structure and performance analysis of a serial hydraulic brake valve, a simulating model of responding characteristics in a full power hydraulic brake system was established, and the simulation analysis of various structure parameters of the braking valve affecting the dynamic characteristics of the system was conducted.

在对串联式液压制动阀结构与性能分析的基础上，建立了全动力液压制动系统动态数学模型，并就制动阀结构参数对系统动态性能的影响进行了仿真分析。

The main products are high, midst and lower press brake valve, stop valve, butterfly valve, and screw valve, pipe and non-standard special vale.

主要产品有高、中、低压闸阀、截止阀、止回阀、球阀、碟阀、丝扣阀门管件以及非标特殊阀门。

Different types of valves (including ball valve, butterfly valve, cut-off valve and brake valve) commonly used in designing painting line and their features were introduced.

介绍了涂装线设计中常用的各种类型的阀门(包括球阀、蝶阀、截止阀、闸阀)及其特点。

The steering brake and the emergent brake of the vehicle were realized by a dualpipeline brake system in which an electronichydraulic servo controlled dual brake valve is used to control the dual-chamber brake cylinder.

采用电液伺服控制的双联制动阀控制双腔制动油缸的双路制动方案，实现车辆的行车制动和紧急制动。

Exhaust brake valve is an auxiliary brake, is a necessary supplement to vehicle service brake; it is to use engine as an air compressor to generate brake torque to decelerate the vehicle; normally it is assembled inside of exhaust pipe, and close the valve to clog the exhaust duct as necessary to reach braking.

排气制动阀是一个辅助制动器，是汽车行车制动器的必要补充，是将发动机作一个空气压缩机使用而产生制动力矩从而对汽车产生减速作用，一般安装在排气管中，在需要减速时关闭阀门以阻塞排气通道而达到制动的效果。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。