查询词典 box plane

The instructive conclusion was: 1 under the vertical loading, the shear-lag effect was produced badly, more severer under concentrated loading than under uniform loading .2 the longitudinal bending deformation of the beam flange was true of the imitating plane assumption of deformation . 3 the width length ratio was confirmed as the first factor working on the shear-lag effect among all the geometric parameters;4 the shear-lag coefficient of simple-supported box-girder was severer than the continuous box-girder, the shear-lag effect in the inner supported section of continuous beam was much more severer, we need paying more attention for it in designing. 5 the non-liner characteristics of material deformation have littlie influence on shear-lag effect in BGCW. 6 the experiential calculating formulation and calculating diagram for the effective flange width was raised with the only factor of the width-span ratio., but the primary location of axis of bending moments should not be changed while calculating the inertial moment .

研究认为：1室内模型试验和空间有限元分析结果均表明波形钢腹板组合箱梁在竖向荷载作用下，翼板出现了典型的纵向应力剪滞效应。2在竖向荷载作用下，截面高度上各点纵向正应变分布认为可符合"拟平截面假定"，以此作为波形钢腹板组合箱梁抗弯计算的基本假定。3箱梁宽跨比是影响波形钢腹板组合箱梁翼板剪滞效应的主要因素。4连续波形钢腹板组合箱梁的翼板剪滞系数大于简支梁，且连续箱梁内支点截面翼板剪滞效应相当严重，对此需十分重视。5当混凝土翼板受力由弹性阶段进入弹塑性阶段时，材料的非线性特性对翼板的剪滞效应影响甚微。6提出了根据组合箱梁的宽跨比参数来计算翼板有效宽度比的经验公式和计算图表，但箱梁截面抗弯惯性矩的计算不应改变原先的截面中和轴位置。

Decomposition to plane circuitry's pin, then aborative go along transmit and insulate inspect, eliminate circuitry malfunction. Aborative analyze to design circuitry, find out join circuitry of flap electric operation system with undercarriage control and beaconage's join circuitry existed circumfluence phenomena. Bring about when undercarriage control signal system electrify inspect, under flap system are not power supply, current from undercarriage signal breaker come by undercarriage signal box, to flap system's flap control box, flap electromagnetism clique form loop. Lead to the flap put down under flap system are not power supply. Design principium existing serious limitation, put forward ameliorate project.

通过对机上线路的插头进行分解，进行导通和绝缘检测，排除了机上线路故障；通过对设计线路进行分析，发现在襟翼电气操纵系统与起落架收放操纵及信号系统的交联线路存在回流现象，致使在起落架收放操纵及信号系统通电检查时，襟翼系统不供电的情况下，电流从起落架信号断路器经过起落架信号盒，到襟翼系统的襟翼控制盒、襟翼电磁阀形成回路，导致襟翼在不给电的情况下被放下，设计原理存在严重的缺陷，提出了改进方案。

Data structure used for interactive design of 3D box CAD and pickup methods of three level objects in plane,line in a plane,and point in a plane were introduced. The interactive 3D paper box CAD system was developed.

给出满足三维包装纸盒交互设计的数据结构和对于面、面内线段、面内点3个层次对象的拾取方法，并开发了交互式三维包装纸盒CAD系统。

The metal mold design now adopt a form of one mole but six cayities ,this way can improve the efficiency;the mold's joint face is the ball's neutral plane,that makes the mold opened convenient;In the gating,the runner and the riser is the same ,and this design adopt scum riser,that make sure a better routing and make sure the casting's feeding;the mold use gravity to lockwasher itself;the core's material is quartz sand,and spread high tempearature resistant dope on it;In the design, same taper in the guide bush of the core box is needed to make sure open the mold easily;The insert blocks of the core box are made by numercial control processing,this way reduce the cost of production; the scale division positioner make sure the same specification has better interchangeability,also,as all the machining can be finished on the general machine tool,it make the cost low,so it can be spreaded abundant in the medium and minor enterprise;when workout the mold's processing technology,this design adopt the rough's two end plane as benchmark,the ball cavities are machined by scale division positioner;then use Autocad,Pro/e to draw planar and three dimension blueprint,use Pro/e to make three-dimensional animation.

本次设计的群铸模具采用一模六腔形式，生产效率高；模具分型面选择磨球的中性面，使得分模方便；浇注系统采用浇冒口一体形式和集渣包设计，保证了良好的加工工艺和补缩；锁模方式为重力锁模；砂芯采用石英砂，并在表层涂以耐高温涂料；芯盒导套选择一定的锥度，使取模容易；芯盒镶块运用数控加工，降低了生产成本；分度胎具保证了同种规格模具具有良好的互换性，而且因为所有加工基本都可以在普通机床上完成，生产成本低，可以为中小型企业普遍采用；在加工工艺编制过程中，采用两端面互为基准，球腔用专业夹具加工；Autocad，Pro/e分别制作了模具的二维和三维立体图，并运用Pro/e制作了三维动画演示。

The metal mold design now adopt a form of one mole but six cayities ,this way can improve the efficiency;the molds joint face is the balls neutral plane,that makes the mold opened convenient;In the gating,the runner and the riser is the same ,and this design adopt scum riser,that make sure a better routing and make sure the castings feeding;the mold use gravity to lockwasher itself;the cores material is quartz sand,and spread high tempearature resistant dope on it;In the design, same taper in the guide bush of the core box is needed to make sure open the mold easily;The insert blocks of the core box are made by numercial control processing,this way reduce the cost of production; the scale division positioner make sure the same specification has better interchangeability,also,as all the machining can be finished on the general machine tool,it make the cost low,so it can be spreaded abundant in the medium and minor enterprise;when workout the molds processing technology,this design adopt the roughs two end plane as benchmark,the ball cavities are machined by scale division positioner;then use Autocad,Pro/e to draw planar and three dimension blueprint,use Pro/e to make three.dimensional animation.

本次设计的群铸模具采用一模六腔形式，生产效率高；模具分型面选择磨球的中性面，使得分模方便；浇注系统采用浇冒口一体形式和集渣包设计，保证了良好的加工工艺和补缩；锁模方式为重力锁模；砂芯采用石英砂，并在表层涂以耐高温涂料；芯盒导套选择一定的锥度，使取模容易；芯盒镶块运用数控加工，降低了生产成本；分度胎具保证了同种规格模具具有良好的互换性，而且因为所有加工基本都可以在普通机床上完成，生产成本低，可以为中小型企业普遍采用；在加工工艺编制过程中，采用两端面互为基准，球腔用专业夹具加工；Autocad，Pro/e分别制作了模具的二维和三维立体图，并运用Pro/e制作了三维动画演示。

In order to understand the dynamic property of extradosed cable-stayed, built up its plane continous rigid-frame model and compared with each other, concluded that the former is more complex due to the remarkable coupling effect of cable, pylons and box-girder. The dynamic property of box-girder decide the dynamic property of the bridge, whose whole structure is comparative rigid. This paper indicated that the bridge is not attribute to flexible structure, because its basic free vibration cycle is more shorter than the cable-stayed bridge.

为了更好的理解矮塔斜拉桥的动力特性，还建立了平面梁单元的连续刚构模型，并与平面梁单元的矮塔斜拉模型进行了对比分析，结果表明，矮塔斜拉模型由于索、塔、梁的高阶振型耦合显著，其振型较连续刚构复杂，灵江大桥的动力特性主要由主梁的动力特性决定，其结构整体刚度较大，基本自振周期较斜拉桥短，不属于柔性结构。

Presenting the calculating method of the space displacement model of skewed box girder, whit main ideas of: dispersing the skewed box girder into some skewed beam segments and further dividing those segments into some plate pieces according to their forms; describing the displacement functions in the plane of plate piece by assuming that the space displacements of any point in the joint line between the plate pieces are described by using Hermite interpolation functions and that two displacements in the plane of plate piece are linear in the cross direction; Using Hermite interpolation functions to describe the bending the displacement of the unit length transverse frame cutting longitudinal from the skew box girder segment; Finally, describing the space displacements of a point in the plate pieces by two displacements in the plane of the plate and one bending displacement of plate.

提出了斜交箱形梁空间位移场的计算方法：将斜交箱形梁沿纵向离散为若干斜梁段单元，依据箱梁的构成进一步将斜梁段划分为若干板段子单元；各板段联结线上任意点的位移按Hermite函数插值，假定各板段的面内位移沿其宽度方向线性变化，以描述各板段面内位移；沿斜交箱梁段的纵向截取单位长度横截面框架，框架各杆件空间位移按Hermite函数插值，以描述各板段面外位移；板段内任意点的空间位移最终以2个面内位移和1个面外位移描述。

The design method of plastic strcuture is mainly introduced . The selection of the sidewall thickness, the decision of the mould cavity number, the selection of injection machine, and the designing process of the parting plane, the exhaust system, cool material cave and pin gate are stated. The design structure characteristics of box cover and parting plane with pin gate style, and side core-drawing structure.

重点说明了电器盒的塑件结构的设计包括分析和阐述了电器盒塑件的壁厚选择及工艺特点；针对塑件的工艺特点进行模具的设计包括模具型腔数目的确定，注塑机的选择，模具分型面、冷却系统、浇注系统、分型抽芯机构等的设计过程。

The universal powder box includes one box with powder bin and cover, one stirrer inside the powder bin, one powder feeding roller in the outlet of the powder bin, one developing roller contacting with the powder feeding roller and one locking device for the powder box to be set in and taken out from the sensitive drum. The cover has one upper planar surface, and after being installed, the plane is located below one corresponding raised edge of the printer. In the roller end gear combination outside one side wall of the box, there are two with driving force driving position.

包括一个带有粉仓的盒体和盖，位于粉仓内的搅拌装置，一个位于粉仓出口处的送粉辊、一个与送粉辊接触的显影辊，及使粉盒能顺利置入或取出感光鼓盒的锁放装置，盖的上表面基本是一个平面，装机后该平面位于打印机对应盖下表面凸起的下缘之下，在盒体一个侧壁外的各辊端齿轮组中，有两个带有动力受口的驱动位。

One summer they planned to fly to New York for their holidays.They got to the airport only ten minutes before the plane left.So time was short.But suddenly Mrs.Long said she must tell Linda,their daughter,not to forget to lock the front door when she went to school.As Linda was than at school,they coundn't tell her about it by telrphone.So the couple hurried to the post office.Mrs.Long wrote a short note to Linda while Mr.Long bought a stamp and an envelope.Soon the note was ready.They put the stamp on the envelope in a hurry and put it in the letter box.But suddenly Mrs.Long began to try.The short note was still in her hand.She had put the plane ticket in the envelope.

一个夏天他们计划飞往纽约度假，他们在飞机离开前仅十分钟才到了飞机场，所以时间很短，但是突然Long太太说她必须去告诉他们的女儿Linda，当她上学时不要忘记锁自家的前门，现在女儿正在学校，他们不能用电话告诉女儿，所以这对夫妻很快去了邮局，当Long先生买了一枚邮票和一个信封时，Long太太写了一个小纸条给Linda，很快纸条写好了，他们很快把邮票贴在信封上，之后把它扔进信箱里，但是突然Long太太开始哭，那个小纸条还在他的手上，她已经把机票放在了信箱了！

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐