查询词典 box beam

The actions of traffic and environment lead to joint failure, which allows deicer solutions to pass through the joint onto the pier caps and beam-ends in I-beams, and onto the sides of box beams.

行动交通和环境导致联合失败使除冰办法通过联合走上墩帽梁端的I型梁，带上方箱梁。

In this paper, draw the idea of beam unit, the bias along the vertical box is divided into a number of oblique beam. On the basis of analysis of the displacement, through positive and oblique coordinate transformation relations, and directly built on the oblique coordinate system to describe the methods of displacement unit space. With potential energy principle is derived in oblique beam element stiffness matrix and the establishment of the finite element formulation. The preparation process of the finite element analysis is used to verify the structure of bias.

本文吸取梁段单元的思想，将斜交箱梁沿纵向划分为若干斜梁段，在位移分析的基础上，通过正、斜交坐标转换关系，直接建立在斜交坐标系内描述单元空间位移的方法，用势能驻值原理推导斜梁单元刚度矩阵并建立其有限单元列式，利用编制的有限元程序进行斜交结构的分析。

The method for design thin-wall core box cast-in-site concrete hollow floor using common structural computing software is put forward and the scale for the magnifying stiffness coefficient of the spandrel beam and middle beam is discussed.

提出了采用常用的结构计算软件计算薄壁箱体现浇混凝土空心楼盖设计的方法，提出了边梁和中梁刚度放大系数的建议。

The company's main business areas: 1, cylinder, square cylinder, cone-shaped mound, hollow pier, abutment, guard-rails, tie beam, beam cap, hollow beam, box girder, T girder bridge templates and other design and processing.

1，圆柱、方柱、锥形墩、空心墩、桥台、护栏、系梁、盖梁、空心梁、箱梁、T形梁等各种桥梁模板的设计与加工。

Key words:big space; composite box; net beam ceiling; rib beam; board uniting with beam; polymerization cement slurry

关键词］大空间；叠合箱；网梁楼盖；肋梁；梁板合一；聚合水泥浆

Therefore this article introduced the use space surrounding box carries on fast beam tracing on the triangular net model the method, uses this method to be possible fast to complete the up to ten thousand strip beam on the complex model beam tracing, has the very strong practical value.

因此本文介绍了利用空间包围盒在三角网模型上进行快速射线追踪的方法，利用该方法可以在复杂模型上快速完成上万条射线的射线追踪，具有很强的实用价值。

Presenting the calculating method of the space displacement model of skewed box girder, whit main ideas of: dispersing the skewed box girder into some skewed beam segments and further dividing those segments into some plate pieces according to their forms; describing the displacement functions in the plane of plate piece by assuming that the space displacements of any point in the joint line between the plate pieces are described by using Hermite interpolation functions and that two displacements in the plane of plate piece are linear in the cross direction; Using Hermite interpolation functions to describe the bending the displacement of the unit length transverse frame cutting longitudinal from the skew box girder segment; Finally, describing the space displacements of a point in the plate pieces by two displacements in the plane of the plate and one bending displacement of plate.

提出了斜交箱形梁空间位移场的计算方法：将斜交箱形梁沿纵向离散为若干斜梁段单元，依据箱梁的构成进一步将斜梁段划分为若干板段子单元；各板段联结线上任意点的位移按Hermite函数插值，假定各板段的面内位移沿其宽度方向线性变化，以描述各板段面内位移；沿斜交箱梁段的纵向截取单位长度横截面框架，框架各杆件空间位移按Hermite函数插值，以描述各板段面外位移；板段内任意点的空间位移最终以2个面内位移和1个面外位移描述。

Using the software of ansys, this thesis compares and analyzes the seismic behavior of the joint of cold-formed rectangular tube-steel column and H-shaped beam and the joint of welding box column and H-shaped beam, in order to research the influence for the cold forming process of the cold-formed rectangular tube-steel column.

利用大型通用有限元分析软件，对冷弯矩形钢管柱与H型钢梁连接节点与焊接箱形钢管柱与H型钢梁连接节点的抗震性能进行对比分析，探讨出冷弯矩形钢管的特性对节点抗震性能的影响。

Thesis is divided into five parts, the main contents include: a long beam and truss repair and strength calculation, Liang Lu-board repair, the following box and wing rib repair, box rib injury at the time of small-scale repairs, large-scale box rib injury at the time of repair and a new frame, the positioning rib installation.

论文共分5个部分，主要内容包括：梁和长桁的修理及强度的计算、梁履板的修理、隔框和翼肋的修理、框肋小范围损伤时的修理、框肋大范围损伤时的修理及新框、肋的定位安装等。

Adopt the ontology to set a physical analysis model of box section beam and carry outfinite element analysis of upper beam for the electrical operated screw tire shaping curing press, basedon the foundation of confirming the structure of the beam, presented the relative improved method.

用实体元素法建立了箱型截面梁的物理分析模型，并对电动螺旋轮胎定型硫化机的上横梁进行了有限元分析，在对上横梁的结构肯定的基础上提出了相应的改进措施。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。