查询词典 boring tube

Test combinations tipping platform, laboratory basic platform, electrical test bench, round platform, floor boring machine table, boring and milling machine table, vertical table, gantry milling bed table, resin sand cast iron bed, column, mold plate and other large castings.

检验组合接装平台、实验室基础平台、电机试验台、圆平台、落地镗床工作台、镗铣床工作台、立式工作台、龙门铣刨床工作台、树脂砂铸铁床身、立柱、模具垫板等大型铸件。

LiWei INC was founded in 1999, integrating scientific research, design, production, operating in one, professional production and sale of Rock Drilling, mining accessories, engineering tools, rock drilling tools, milling machine milling teeth, milling Machine Cutter, road Mixer Cutter, coal mine cut teeth with various types of Shearer with conical teeth, knife-shaped cross-sectional tooth, boring machine with boring tooth, shield knives, metro shield machine shield configuration tools and various types of mining bits, rock drills, anchor drills, rotary drilling engineering cut-off teeth, using rotary drilling rig Rotary Drilling teeth, tooth roadheader, Rotary Drilling teeth, bucket teeth, tooth Block, and a variety of Rock Drilling Bits, including word, cross drill head, the ball tooth drill head, drill sets, drill tail, drill rod and so on.

香港立威刀具有限公司始建于1999年，集科研、设计、生产、经营于一体，专业生产和销售凿岩钎具、矿山配件、工程工具、岩土钻掘工具、铣刨机用铣刨齿、铣刨机刀头、路拌机刀头、煤矿用截齿、各种型号的采煤机用镐形截齿、刀形截齿、掘进机用掘进齿、盾构刀具、地铁盾构机用盾构刀具及各种型号的矿用钻头、岩石钻头、锚杆钻头、工程用旋挖截齿、旋挖钻机用旋挖齿、掘进机截齿、旋挖齿、斗齿、齿座和各种凿岩钎具包括一字钎头、十字钎头、球齿钎头、钎套、钎尾、钎杆等。

Comparing with boring bar,numerical results reveal that boring bar with dynamic absorber has the effect of vibration decrease.

通过和普通镗杆对比分析，结果表明动力减振镗杆有效地达到了减振效果。

Processing needs boring bar diameter 160 ~ 250mm floor of CNC boring and milling machine and large-scale horizontal machining center, gantry machining centers, machining accuracy are higher, and at present is still mainly use imported equipment.

加工需要镗杆直径约160～250mm的数控落地铣镗床和大型卧式加工中心、龙门加工中心等，加工精度要求较高，目前主要使用的仍是进口设备。

Modeling and derivation mathematics result of the use of Matlab software Simulation tests of its accuracy and error analysis, to verify the measurement of two boring bar/boring displacement signal the feasibility of the entire system, so as to the smooth development has laid a theoretical foundation.

介绍了两点法测量镗刀位置信号的方案构思，采用最小二乘法对镗杆的圆度误差和被测圆面的偏心量进行了建模计算，并对数学推导的结果利用Matlab软件进行仿真检验，对其精度和误差作了分析，验证了两点法测量镗杆／镗刀位移信号的可行性，从而为整个系统的顺利开发奠定了理论基础。

A sample analysis is given, and the stress distribution within the boring bar and the maximum deflection are obtained under a given cutting condition, at the same time, the comparative analysis with a common type boring bar with the same size is pursued.

给出了分析实例，得到了该种镗刀杆在给定切削条件下的应力分布以及最大挠度并与相同尺寸的普通镗刀杆进行了对比分析。

The only major difference is that boring jigs are normally fitted with a pilot bushing or bearing to support the outer end of the boring bar during the machining operation.

唯一最重要的差别是镗夹具一般用于控制衬套，或者在机器操作时支撑镗杆的外端。

The outer diameter of the boring bar is strictly limited by the size of the bored hole. In order to solve this problem, the first new structural micro-boring bar system with the function of active error compensation was developed.

在车削、铣削和磨削等外表面加工中，误差补偿用微进给刀架的结构形状、尺寸和体积都没有严格的限制，误差检测传感器和补偿驱动传感器能够方便地安装在微进给刀架内。

One kind of PCD boring tool and a fine adjustment boring bar,which are suitably used in precision finishing the surface of pinhole of combustion engine piston,are introduced.

介绍了一种适用于发动机活塞销孔表面精镗加工用聚晶金刚石镗刀和可微调刀具尺寸的精密微调镗杆，该镗刀和镗杆组合具有较高的加工精度和表面粗糙度精度以及调整方便、使用寿命长的特点。

On the base of studying the forming mechanism of spire ditches in deep-hole boring process, this paper analyses theoretically the effect of the boring bar diameter on the oscillation and spire ditches and established the mechanical model.

在研究深孔镗削螺旋沟产生机理的基础上，对深孔镗削加工过程中镗杆直径对振动及螺旋沟的影响进行了理论分析及力学建模，并通过试验研究了增大镗杆直径对减小振动和抑制螺旋沟的积极作用。

A small, rubber-headed hammer used in examination or diagnosis by percussion.

叩诊槌用在通过''。'振荡'。''所作的检查或诊断中的橡皮头的''。'小'。''槌

Affixes are limited in number in a language, and are generally classified into three subtypes, namely, prefix, suffix, and infix, depending on their position with reference to the root or stem of the word.

语言中词缀的数量总是有限的，根据它们跟词根或词干的相对位置，一般可以把词缀分外三小类：前缀，后缀和中缀。