查询词典 bore a hole

Mark the line for the socket hole on the back panel and use the jig saw to cut along the marked line.

吊柜上部我们可以以挂件中点为标准，侧面以吊柜侧板作为标准来测量，并在背板上划好插座孔线，用穿梭机沿线切割。

Uses tape to measure the hole positions for the jointers and mark the line. Then, install the jointers on the door panels at the marked line.

先用卷尺测量好前接码的孔位尺寸，然后按测量的尺寸在门板上画定位线。

The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used for removing the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Firstly, let us install the jointers in the drawer frame. There are three adjusting parts on the sides. The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used for removing the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Firstly, let us install the jointers in the drawer frame. There are three adjusting parts on the sides. The front part is used for adjusting the left and right sides of the drawer door panels, the back part is used for adjusting the up and down of the door panels and the hole in the middle is used forremoving the jointers.

首先把前接码插入抽帮里面，侧面有三个调整件，前面一个用于调整抽屉门板左右摆动；后面一个用于调整门板上下摆动，中间的孔位用于拆卸前接码。

Based on the geophysical prospecting material on the 11105W working surface and the neighbor drill hole in xiezhuang coal field of shandong province,the appraisal and forecast has been carried on the developing degree of karsts in Ordovician limestone and its water-bearing degree under this working surface floor.

依据山东省协庄井田11105W工作面的物探资料和附近的钻孔资料，对该工作面奥陶系灰岩岩溶发育程度、富水性进行了评价及预测，最后对11105W工作面底板奥陶系灰岩突水的可能性进行了分析和评价

Since the method causes serious depletion of ore during mining of upper plate,the inclined cutting raise heading together with inclined medium or deep hole kerve is suggested.

以无底柱为代表的崩落采矿法中，切割拉槽至关重要，而目前无底柱采矿大多采用垂直切割天井与切割平巷并配以中深孔联合拉槽的切割方法，但该方法在对矿体上盘回采过程中损失贫化较大。

In this paper combined with actual works the design and construction method are introduced that applying pouring joist with pin key one existing brick wall to form a wall beam with upper masonry enhances the wall's load after cutting a big hole in it.

结合工程实例，介绍了在已有砖墙上浇筑带销键的托梁，与上部砌体形成墙梁来承托开凿宽大窗洞后的洞顶墙体荷载的设计、施工方法，指出该方法取得了良好的应用效果，既加快了施工进度，又降低了造价。

Both ends of the die cutting knife vrachyaxis are used with hole Loy, wood box fixed to prevent transportation die-cutting knife inter-articular in the box.

模切刀两头的长轴需不分别用带孔的木块套上，木块在箱边固不退，制止输送洋模切刀在箱边移位。

Two multicolored ceramic plates, an alabaster vase with a hole in the base, and a stone knife also accompanied the body.

两个多彩的陶瓷盘子，一个底部破裂的条文大理石花瓶，和一把石刀伴随着尸骨。

It is possible that houses were outrageously priced one year ago and that they are still priced much higher than the national average.

情况有可能是，这里的房价曾贵得离谱，现在的房价仍然远高于全国的平均指数。

This is a mother's love for her child.

这是母亲对孩子的关爱。