查询词典 bolt

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

And we has also accumulated original and mature experience in designing, manufacturing and assembling of bolt tightening system, press riveting and welding system, automobile seatbelt assembling special machine, pin and shaft press installing machine, transplanting machine, aerial material flow line, material flow line, lifting equipment, balance crane, fixture etc.; To meet its clients' demand, Congyu has independently developed many sets of special machine of high technology and great difficulty, which involves the clearance detection, angle control, sealing test, torque control and displacement control etc.

并在螺栓拧紧系统、压铆焊接系统、汽车安全带装配专机、销轴压装机、移栽机、空中物流输送线、物流输送线、提升机、平衡省力装置、各种产品的工装夹具等方面有独到成熟的设计、制造及组装经验；应客户要求独立开发出多套间隙检测，角度控制，密封性检测，扭矩控制，位移控制等高技术、高难度要求专机，在此基础上，不断创新并开发了清洗机等新产品和太阳能新领域，并为太阳能行业开发了自动上下料机、酸碱清洗机和自动插片机，接线盒涂胶机，自动裁切机，测试分选机等一系列生产和测试设备。

The cause of joint failure is studied by analyzing the failure phenomena of grid structure bolt ball joint.

通过分析螺栓球网架节点破坏现象，阐述了节点破坏原因。

This mean that after the shot bolt with barrel locked to it are moving backward for some 4 millimeters.

这意味着被锁定后，它的每桶杆螺栓正在落后约400毫米。

To do switch from one caliber to another one must replace the barrel and a bolt head.

要做到从一个口径切换到另一个必须更换枪管和机头。

Then barrel is stopped and the bolt continues back, to extract and eject a spent case.

然后桶停止，螺栓继续回来，提取和弹出一花案。

Note that all [3] cable housings enter a barrel bolt with a lock nut.

请注意，所有[ 3 ]电缆外壳进入每桶螺栓锁螺母。

Calibers can be swapped on one rifle in the matter of minutes by replacing the barrel, bolt and magazine.

口径可以在一个交换在数分钟内通过更换步枪枪管，枪栓和杂志。

It is available in two versions, 20mm and 14.5mm, and could be easily converted from one variant to another by simple replacement of the barrel, bolt, magazine and scope, which will take about 1 minute in the field conditions.

它有两个版本，20毫米和14.5毫米，并且可以很容易从一种变体的枪管，枪栓，杂志和范围，这将在现场条件下大约1分钟的简单更换到另一个。

The entire bolt/barrel group is enclosed in lightweight polymer housing, which protects the mechanisms from elements and rough handling.

整个螺栓/桶组包含在轻量级聚合物住房，它保护的内容和粗糙处理机制。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷