查询词典 blowing mold

From the end of the last century HID come out, I actively participate in research projects xenon lights, the installation of various models by the problems can be understanding and treatment of January 1, and to provide xenon lights and improve the quality of the Requests for the domestic manufacturing enterprises to jointly develop the HID xenon bulbs, after several years of exploration and accumulation of experience, I mature products in a time when, in 2003 started a mold development Jetta headlamps assembly, these two Continuously improved, and finally to the successful production of Jetta headlamps.

从上世纪末HID问世，我公司积极参与氙气灯研究项目，对各种车型安装所出现的问题都能一一了解及处理方法，并提供氙气灯质量和改进工艺的要求给予国内生产企业，共同开发国产HID氙气灯泡，经过几年摸索和积累经验，我公司在产品成熟之际，于2003年着手开模具开发宝来大灯总成，通过这两年不断改良，终于自行生产宝来大灯成功。

I brought out the 3' wrecking bar and slipped the edge through the foam that I used for filler in the back of the mold.

i带出了3 '破坏性的酒吧和下滑的边缘，通过泡沫，我用的填料在后面的模具。

Cake Bakery base, vanilla cake mix, chocolate cake mix, four fondant mixes, rainbow sprinkles, white gel, gel decorator, decorating wheel, microwave baker, microwave baker lid, mixing bowl, cake mold, measuring spoon, tray, spatula, four fondant cutters, utensil holder, work mat, rolling pin, two gel cartridges, cartridge cleaning brush, four recipe cards, and instruction sheet.

蛋糕面包的基础上，混合香草蛋糕，巧克力蛋糕的组合，4翻糖混合物，彩虹洒，白色凝胶，凝胶装饰，装饰轮，微波面包，微波面包盖子，搅拌碗，蛋糕模具，测量勺，盘，铲，四达特刀具，器皿持有人，工作垫，轧脚，两个胶盒，墨盒清洁刷，4食谱卡和说明书。

Using your tamping rod, pack wet concrete into a layer about 2.5 thick in the bottom of your outer mold.

利用成层约2.5在你的外模底厚的捣固棒，包湿的混凝土。

About Zhangjiagang City Hing Wah mold factory was established in 2000, located in the Yangtze River Delta lots of gold, land and sea transportation is very convenient, Nantong north, west Jiangyin, South by Suzhou, east of Shanghai.

张家港市兴华模具厂成立于2000年，位于长江三角洲的黄金地段，水陆交通十分便利，北临南通，西接江阴，南依苏州，东靠上海。

At the same time, professional on staff, the public will also be familiar with "mold","injection wax,""Flower Cart","polished","Gold","playing ground", such as the mysterious stranger to the jewelry before making the name and complex manufacturing processes.

同时，在工作人员专业讲解下，市民也将熟知&倒模&、&注蜡&、&车花&、&抛光&、&电金&、&磨打&等以往陌生神秘的珠宝制作名称和复杂制作工序。

This design topic is the design and manufacture process of thecompand type cast of metal mold for the high chromium white castiron milling of 80 millimeter diameter.

本次的设计题目是80mm高铬白口铸铁磨球金属型复合群铸模具设计及制造工艺。

Centrifuging is used for forcing metal from a central axis of the equipment into individual mold cavities that are placed on the circumference.

离心法铸造：离心法铸造用于迫使金属从设备的中心轴进入分布在圆周上的单独型腔。

Moreover, the electromagnetic flux density and meniscus height increase in the form of chequerboard with increasing of slit number. The numerical results can exactly illuminate some experimental phenomena, and enrich the theoretical foundation of soft-contact continuous casting technology. In practice, a softcontact mold with slit number of 16 or 24 is recommended, the suggested frequency is around 20kHz, and the slit width is about 1mm.

结果表明：钢液对结晶器内的电磁场分布有很大影响；发现了磁感应强度和弯月面高度随电源频率增加而增大的频率范围、磁感应强度和弯月面高度随切缝数目增加呈&锯齿状&增大的规律；研究结果合理地解释了一些实验现象，完善了软接触结晶器电磁连铸技术的理论基础；建议在实际应用中采用分瓣数为16或24分瓣数的结晶器，电源频率应控制在20kHz左右，切缝宽度应控制在1mm左右。

C, Injection Molding: injection molding stage is the injection screw in the fuel tank thrust, in the Reserve Room of the expected melt through nozzles, mold flow, the gate into the cavity.

三，注塑充模：注射充模阶段是螺杆在注射油缸推力作用，将储料室中的熔体经过喷嘴、模具流道、浇口注入型腔。

Finally it offers the analysis of the fault-tolerance system as well as its test verification.

这样，运行于空间环境中的系统的设计目标就是在保证系统实时性

However, it is still difficult to find out the real reason of the increase of the keratinized gingiva during the orthodontic extrusion whether it is due to the proliferation of the gingival tissue or to its elastic nature, that is because the proliferation of the fibroblasts as well as the connective tissue changes in volume and the intra-fibers spaces were all immeasurable in most of the studies.

然而，仍然难以找到真正的原因增加的角化牙龈在正畸挤压它是否是由于扩散的牙龈组织或其弹性性质，这是因为增殖的成纤维细胞以及作为结缔组织的变化量和内部纤维空格都是不可估量的，大多数的研究。