查询词典 blow by blow

When we was three-quarters of a mile below we hoisted up our signal lantern; and about ten o'clock it come on to rain and blow and thunder and lighten like everything; so the king told us to both stay on watch till the weather got better; then him and the duke crawled into the wigwam and turned in for the night.

等到开出下游四分之三英里，我们就挂起了信号灯来。十点钟光景，又是大雨倾盆，又是雷电交加，闹得不可开交，所以国王交代我们两人都要留心看守好，一直要等到天气好转。随后，国王和公爵爬进窝棚宿夜。下边是该我的班，要值到十二点钟。

The bespoke design is blow moulded in HDPE , with an attractive curved shape and a distinctive raised band across the side of the container .

在定制的设计是在高密度聚乙烯吹塑成型，与一个有吸引力的弯曲形状和鲜明提出带跨一侧的容器。

Some of those flashing energy blasts were as big around as his en tire ship; the merest graze would blow him to atoms.

其中一些闪烁的能量束甚至有他的整架战机那么粗，哪怕只是擦到那么一下都能立即将他分解成原子等级的东西。

and will increase damage taken by 100% so its important that you try not to tank when you have this. It will eventually become unavoidable near the end of p1 so just save a shield wall for when you need to blow up your guardian.

女人会给玩家一个增加受到伤害100%的debuff，在你有得时候别坦克，到了第一阶段的最后，几乎不可避免你会有这个debuff，最后留一个保命集能在最后当你在最后坦克引爆小怪的时候用。

He raised his arm to shield himself from the blow.

他举起手臂保护自己不挨打。

The company has developed three types of mold and the three series of species: the three major types: the first category, plastic (such as: injection molding, blow molding); the second category, die-casting mold (such as: aluminum die-casting); third type, sheet metal mold (such as: stamping die, tensile modulus).

公司主要研制开发的模具有三大类型和三大系列品种：三大类型：第一类，塑料模；第二类，压铸模；第三类，钣金模。

The bearing inner ring and the axis tight fit, the outer ring bearing hole is a more loose with the non-separation-type bearings installed, press the bearings can be installed on the shaft, then shaft with bearings packed together into the bearing hole inside, if the bearing is small, can also be lighter than the soft metal hammer blow set

对无油轴承内圈与轴时紧配合、外圈轴承座孔是较松配合的非分离型轴承进行安装时，可用压力机将轴承先安装在轴上，然后将轴连同轴承一起装到轴承座孔内，若轴承较小时，也可用较软的金属锤轻击套

I have an independent mold factory workshop, blow / injection molding workshop, self-opening mode, sample / material processing all kinds of plastic electrical accessories and plastic blowing / injection plastic products.

我厂拥有独立的模具车间，吹/注塑车间，可自行开模，来样/料加工各种塑料电器配件及塑料吹/注塑料产品。

And after these things I saw four angels standing on the four corners of the earth, holding the four winds of the earth, that the wind should not blow on the earth, nor on the sea, nor on any tree.

001 此后，我看见四位天使站在地的四角，执掌地上的四风，叫风不吹在地上、海上，和树上。

After this I saw four angels standing at the four corners of the earth, holding the four winds of the earth, so that no wind would blow on the earth nor on the sea nor on any tree.

7：1 这事以后，我看见四位天使站在地的四角，执掌地上四方的风，叫风不吹在地上、海上和任何树上。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。