查询词典 bite

The Best Cheddar gong went to Quickes in Devon which produces an outstanding mature traditional cheddar that is the colour of freshly churned butter, whiffs of farmyard and has a creamy, sweet, crystallised bite.

最佳切达锣前往德文郡的 Quickes 而产生一个优秀成熟的传统切达这是新鲜搅动黄油，在农家庭院whiffs和有奶油，甜，咬色结晶。

My baby more than three months, when infants are always bite me, why?

我的孩子三个多月，总是在吃奶的时候咬我，是为什么？

Robyn took a large bite out of her sandwich.

罗宾从她的三明治面包咬下一大块。

She says,"I'm afraid of the tigers standing below, as they can bite."

她说，&我怕下面的老虎，它们会咬人。&

Featuring addictive time management action, simple mouse controls and graphics that show off the striking beauty of the marine world, the bait has been set. Will you bite?

这是款吸引人的时间管理动作游戏，简单的鼠标操作与漂亮的游戏画面将使惊人美丽的海洋世界尽显你的眼帘，这款游戏就是这麽棒，你会不禁尝试吗？

Featuring addictive time management action, simple mouse controls and graphics that show off the striking beauty of the marine world, the bait has been set. Will you bite?

这是款吸引人的时间管理动作游戏，简单的鼠标操作与漂亮的游戏画面将使惊人美丽的海洋世界尽显你的眼帘，这款游戏就是这栾棒，你会不禁尝试吗？

Butt Weld and docking and corner combinations Weld, in Weld ends located arc plate and extraction plate in igniting board then leads to the welding seam, joint halfway shall weld joints in front of 2.0 mm Department Firing arc, welding pieces after preheating rod will return to weld the origin, pool filled to the required thickness, before forward welding; Welding speed : Isokinetic welding requirements to ensure weld thickness, width uniform, which masks to look for hot metal and slag bath equidistance (2-3 mm)%; Arc welding rod length : different models and determined that the general requirements of arc length is stable, acid electrode generally 3-4 mm, 2-3 mm normally alkaline electrode%; Welding perspective : According to determine the thickness of two pieces of welding, welding angle has two aspects : First, the angle between the direction of the rod and welding of 60-75 ; The second is the angle between two electrodes and welding around, the same thickness as welding, welding and welding pieces incident angle of 45 ; When the thickness ranging from welding, welding electrode and thick and thin pieces of welding electrode side angle greater than the angle between the side pieces; Arc : admission to the end of each weld should be filled crater, in the direction opposite to the direction of the back-arc welding, arc welding unchanged inside pit in 1974, to prevent the crater bite of meat.

对接焊缝及对接和角接组合焊缝，在焊缝两端设引弧板和引出板，必须在引弧板上引出后再焊到焊缝区，中途接头则应在焊缝接头前方15～20㎜处打火引弧，将焊件预热后再将焊条退回到焊缝起始处，把熔池填满到要求的厚度后，方可向前施焊；焊接速度：要求等速焊接，保证焊缝厚度、宽度均匀一致，从面罩内看熔池中铁水与熔渣保持等距离（2～3㎜）为宜；焊接电弧长度：根据焊条型号不同而确定，一般要求电弧长度稳定不变，酸性焊条一般为3～4㎜，碱性焊条一般为2～3㎜为宜；焊接角度：根据两焊件的厚度确定，焊接角度有两个方面，一是焊条与焊接前进方向的夹角为60～75 ；二是焊条与焊接左右夹角有两种情况，当焊件厚度相等时，焊件与焊件夹角为45 ；当焊件厚度不等时，焊条与较厚焊件一侧夹角应大于焊条与薄焊件一侧夹角；收弧：每条焊缝焊到末尾，应将弧坑填满后，往焊接方向相反的方向带弧，使弧坑甩在焊道貌岸然里边，以防弧坑咬肉。

In particular, when PHA is inserted beneath the thin skin of a bird's wing, it causes a swelling a bit like a mosquito bite.

尤其是，当这种物质被注射如鸟类翅膀下很薄的皮肤时能够产生蚊子叮咬一样的肿包。

Strukli is the fresh cheese dumplings, pan fried with bread crumbs and served with sour cream, it's crispy when you bite and soft inside, the cheese is toying on your tongue.

Strukli类似中式的水饺，不过里面包的可是芝士，配上上头的脆脆面包碎，外脆内软好不过瘾。

Uh-uh.Can't have you people just breaking off a piece of me every time your stomach growls and then taking a little bite and throwing the rest away.

不能再让你们这些人每次肚子咕咕作响时，就从我身上取下一块，然后只吃一点就扔掉了。

The work of this paper is as follows: 1. Looking back the progressing history of the linear motor, introducing the features of the elevator driven by linear induction motor, radicating the topic of this paper "the digital frequency variable control of the elevator bi-side direct driven by linear induction motor". The research of this paper covers the conventional VVVF control, space vector based VVVF control, vector control and DTC.

本文主要开展了以下几个方面的工作： 1 回顾了直线电机发展历史，电机的驱动技术演变，特别是针对直线电机的驱动，简要介绍了直线感应电机驱动电梯的优点和不同结构类型，对传统的v／f控制，基于空间矢量法的v／f控制，矢量控制，和基于电压空间矢量的直接转矩控制进行了比较，确立了本课题的研究主题：直线感应电机双边直推式驱动电梯的全数字变频控制。

The article combines with the treatment of a superficial civil air defense work to introduce how the grouting method to improve the performance of the backfill soil.

文章从治理漂浮人防工事的角度提出了注浆技术在改善回填土性质方面的应用，并详细阐述了注浆技术的施工流程。