查询词典 billet

Hubei Jingsheng Trading CO., Ltd, established in 2001, specialize in all kinds of steel related products, mainly including resources like slab billet, square billet, coating steel, iron ore, steel scrap , and also finished products hot-roll steel plate/coil, cold-roll steel plate/coil, medium plate, medium thick plate, thick-width steel plate, I-beam and channel steel.

公司简介：湖北景盛贸易有限公司主要从事钢材系列产品的大宗贸易交易。公司主要经营：板坯、方坯、彩板、矿石、废钢等，同时以冷热轧板、中板、工槽钢等品种为辅。

The character and distribution rule of CC round billet internal defect are analyzed and the relation between the defect and process parameters are found, which provide the reference for the billet quality improvement.

本文分析了包钢连铸圆坯内部缺陷的特征及分布规律，找出了内部缺陷与生产工艺参数之间的关系，为改善圆坯质量提供了依

In order to produce the billet without surface defect under high casting speed and to raise the ratio of DHR or HDCR operation and reduce defect ratio of the final products, soft contact EMCC (Electromagnetic Continuous Casting) technique by imposing high frequency electromagnetic field on the molten steel meniscus region has been developed. This technique is used to control the initial solidification of the billet.

为了在高拉速条件下生产出无表面缺陷的铸坯，以进一步增大铸坯HDR或DHCR的操作比率、提高最终产品的无缺陷率，连铸技术工作者开发出利用高频交变磁场对铸坯初始凝固过程进行控制的软接触电磁连铸技术。

The 11 kinds of surface crack features of round cast billet formed by high casting temperature, mould flux lubricating film un-uniform at billet shell, unstale casting speed, tundish nozzle eccentric, alloy steel cast billet cooling and reheating speed overhigh, deleterious elements Pb,Sn,As,Sb and Bi residual content in steel over standard requirements and mould copper tube shifting,...

叙述了浇铸温度高，保护渣润滑膜不均匀，铸坯拉速不稳定，二冷水不均匀，中间包水口不对中，合金钢铸坯冷却和再加热速度过快及钢中五害元素超标和结晶器铜管偏移等致使圆铸坯表面形成的 11种裂纹的特征及其预防措施。

When the billet reduces by 25% in height, the effect of densification for the billet is better, the maximum relative density is 98%.

在315T液压机上实现了高向为200 mm的多孔材料的致密化加工。

The results indicated that during the pressure-keeping stage, the temperature field distributed evenly at the surface and inner part of the billet. In the extrusion process, however, they fluctuated tempestuously which lead to partial overheating on billet surface and result in superficial crack. The flaw analysis and forecast were validated to the experimental result of extruded product.

模拟结果表明，坯料内部和表面的温度场在保压过程中分布均匀，而在挤压过程中则随时间推移而剧烈波动，从而造成坯料表面局部过热，由此导致制件表面龟裂现象的发生。

Heating billet temperature cannot be detected in the hearth. Only by detecting temperatures of the stove side or hearth with estimation from mere experience could lead to great error on the measurement of billet temperature and affect the quality of post-processing accordingly; Overheating also exists in the heating process, and the quality of product is sway by overheating oxidation. Though infrared thermoscope is used to detect the temperature of billet when it is taken out of the stove, precision is still affected because of the oxide layer on the surface.

燃气与空气的配气量比例，一般通过人工调节，未实现按加热条件自动动态调节；无法在炉膛内检测被加热钢材的温度，只能通过检测炉壁或炉膛温度，再凭经验估计钢材温度，结果是钢板温度误差大，影响后续加工质量；钢材加热存在表面过烧现象，有时表面烧损、氧化严重，影响产品质量；尽管钢材出炉时，可用红外线测温仪来进行钢材表面温度检测，但因钢材表面存在氧化层，也影响钢材温度检测精度。

According to the case of billet heating in a regenerative type heating furnace, the temperature distributing of billet about upper surface, undersurface and center surface in length and width is studied by computational fluid dynamicsin this article, and the questions of billet such as different temperature of upper surface and undersurface, the higher temperature of foursquare margin and the lower temperature of tapping orifice are put forward.

中文摘要：借助CFD仿真手段，模拟蓄热式加热炉内钢坯加热的实际状况，研究了钢坯长度、宽度方向上下表面和中心温度的温度分布，提出钢坯存在上下温差、四角边缘温度高和靠近出钢口钢坯温度低等问题。

This paper introduces the main equipments of this system, such as pinch roll, billet descaling, billet welding; burring; movable roller bed; billet insulation and welder hydraulic station, etc.

介绍了无头轧制系统的夹送辊、钠坯除鳞、钢坯焊接、毛刺清理、活动辊道、钢坯保温、焊机液压站等主要装置。

The experiment and the research indicate that:(1) Through the Hot-Continuous-Rolling production technics under small reduction ratio of 4.04 and 5.08, the rectangular continuous-casting billet of 235×265mm can be used to produce big size steel stick of Φ140mm and Φ 125mm whose macrostructure and mechanical properties meet the standards, this technics is viable;(2) This rolling technics can make the deformation penetrate to the center of the billet by low temperture and low velocity and big roller diameter and large reduction quantity at every pass and optimum design and arrangement of rollers, which is the key of Hot-Continuous-Rolling technics under small reduction ratio;(3) The sending technics used in Xining Special Steel Co.,Ltd can not use waste-heat of billet adequately, but the sensitive temperature section of A1N or sulphides or inclusions separating out is avoided, creating a favorablecondition for insuring good surface quality of final rolled steel;(4) The Hot-Continuous-Rolling technics under small reduction ratio has a close relationship with the billet quality control and the hot sending process control and the cooling control after rolling.

通过实验研究表明：(1) 235×265mm矩形连铸坯分别采用4.04和5.08的小压缩比热连轧生产工艺，所生产的Φ140mm和Φ125mm的大规格棒材，其低倍组织和机械性能均符合标准要求，该工艺是可行的；(2)本实验所采取的低温低速、大辊径大道次压下量轧制工艺加上轧辊孔型的优化设计与配置，可以使加工变形渗透到铸坯的中心，这一点是实现小压缩比热连轧生产工艺的关键；(3)西宁特钢在红送过程中虽然铸坯余热未能得到充分的利用，但是有效地避开了A1N、硫化物的析出及夹杂物偏析的敏感温度区，为保证最终轧材良好的表面质量创造了有利的条件；(4)小压缩比热连轧生产与铸坯质量控制，热送过程控制以及轧后冷却控制密不可分。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了