查询词典 big end

Chopsticks uses which in China, cannot knock , namely goes to eat when the waiting, cannot take chopsticks at will to strike or the teacup chopsticks cannot a horizontal vertical stroke alternately place in bowl side, is big end is a capitellum.

在中国用的筷子，不能敲筷，即在等待就餐时，不能一手拿一根筷子随意敲打碗盏或茶杯。筷子不能一横一竖交叉摆放在碗的旁边，一根是大头一根是小头。

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。关键词拨叉，加工工艺，专用夹具，设计

Big, but the end of her dream of finding the proverbial Mr.

Big的关系上来说是这样，对于她的寻找Mr。

The small end of connecting rod acts to-and-fro movement, and the big end of acts circumvolve movement. The connecting rod body acts complex plane movement. The connecting rod is one of the accessories that endures heavy load. And at the same time it endures gas pressure transmitted from the piston, the to-and-fro inertia force and inertia force engendered when itself swings.

连杆工作的小端作往复运动，大端作旋转运动，杆身做复杂的平面运动，连杆是承受负荷最严重的零件之一，同时承受着活塞传来的气体压力、往复惯性力和它本身摆动时所产生的惯性力的作用，这些力的大小和方向周期性变化，易引起连杆疲劳破坏。

Based on the above theories, some vibration characteristics of longitudinal acoustic horns are analyzed with finite element analysis software ANSYS. Some factors influence to large end amplitude distribution is studied such as big end diameter, length of horn, and diameter ratio of big end to small one. In addition, we carry on analysis and research to resonance frequency of large cross-section acoustic horn, amplitude magnification factor, wave node position of horn, transverse vibration situation and so on, and some related change rules are obtained.

在此基础上，通过有限元分析软件ANSYS对纵向超声变幅杆进行了振动特性分析，研究了变幅杆的大端直径、变幅杆长度、大小端面直径比对大端面振幅分布的影响，并对大截面变幅杆的谐振频率、振幅放大系数、变幅杆的波节点位置，横向振动分布等进行了分析研究，总结了相关的变化规律。

The Big-Endian and Little-Endian parties debated over whether soft-boiled eggs should be opened at the big end or the little end.

在小人国里的小人因为非常小（身高6英寸）所以总是碰到一些意想不到的问题。

Last year, the port city enterprise implemented "walks" the strategy to make the new progress, the foreign economic cooperation service has had the large growth, the big project impetus service grew, beyond the border foreign contract engineering service, mainly occupied "the big end" by the architecture industry, realized grew quickly, compared with last year, the rate of rise was remarkable, sends out the population also largely to increase, launches the foreign economic cooperation project, adapted the international contract market development.

提示： 您现在查看的是分类妈妈关于烟台走出去的信息，如果您不满意，请登录咨询建议留言，让我们共同打造港城新媒体！烟台分类妈妈消息，今天一尾号是1384的网民来电说想告诉大家一条关于烟台走出去战略实施的相关信息：去年，港城企业实施&走出去&战略取得了新进展，对外经济合作业务取得了大幅增长，大项目推动业务增长，境外对外承包工程业务，主要以建筑业占&大头&，实现了较快增长，与去年相比，增长速度显著，派出人数也大幅增加，展开对外经济合作项目，适应了国际承包市场的发展。

Big, but the end of her dream of finding the proverbial Mr.

Big的关系的结束，也是她试图发现Mr。

Big, but the end of her dream of finding the proverbial Mr.

Big之间关系的结束，也是她寻找寓言式的Mr。

What would he tell Judith and the children?

他将怎样告诉朱迪丝和孩子们呢？

I this is at that time, the opinion with peacockish true girl is full of in a heart.

这就是当时的我，一个心中布满虚荣的女孩子真实的想法。