查询词典 bib nozzle

Sometimes the nozzle and elastics ink let without cleaning, or rubber band wear rupture, prvent sucking out of paper or is not enough, it will cause empty.

有时呼嘴和橡皮圈上的油墨恒久积聚而未冲洗，或者橡皮圈磨损分裂，在呼纸时漏气或者是不斥力不敷，也会变成不满弛。

Front cover of cam on control block, the position has not changed, the suction nozzle on the cover of the book myoelctricity and kuyto action game disc so there is no conflict, remove the solenoid valve found solenoids for control of the closed part location is not on its base has to turn aside, rustiness in serious and took out a clean sand, abrosive, reset, electrized device are working properly.

控制上封面的凸轮块位置也没有变化，上封面的吸嘴的动作时序与托书盘的动作也没有冲突，拆下电磁阀发现电磁线圈控制的关闭件位置不在其基座上，已经歪斜，锈蚀严重，拿出用砂纸打磨干净、复位，通电设备运转正常。

Distance: the so-called distance refers to the nozzle to the plate surface, which is the distance from the Etchant spray to the substrate surface distance, this is very important.

间隔：所谓间隔是指喷咀到不活背的间隔，也不离是蚀刻液喷淋到基不活暗地的间隔，这是不入格次给的。

The two feasible engineering application curves are given which curve pc*=f1,optimum combustion chamber Pc* versus nozzle expansion ratio ε and curve ε*= f2, optimumnozzle expansion ratio ε versus combustion chamber pressure Pc resoved by iteration method.

用迭代法求解，给出了两条工程上行之有效的曲线──最佳燃烧室工作任强随喷管膨胀比ε的变化曲线和最佳喷管膨胀比ε*随燃烧室工作压强pc的变化曲线。

It was found by water modeling study that there are mainly three types of mold powder entrapment in slab continuous casting, i. e., the entrapment caused by the shearing flow near the narrow face of the mold, the entrapment caused by vortexes in regions around the submerged entry nozzle and the entrapment caused by the disturbing action of the Ar bubbles on the interface between liquid steel and mold powder.

对板坯连铸结晶器保护渣卷渣进行的水力学模拟研究结果表明，主要有三种类型的卷渣，即窄边附近的剪切卷渣、浸入式水口附近的旋涡卷渣和水口吹入的氢气泡上浮冲击钢渣界面引起的卷渣。

Nozzle hole face a pit, to be replaced.

喷嘴孔端面有凹坑，需要更换。

Just when the temperature feals to hot for your hand, turn of the steam while the nozzle is still under the surface.

当你的手觉得温度有些热时，保持喷嘴在液面下面，关闭蒸汽。

This paper narrates the usage and maintenance of semi-automatic CO2 welding torch with feed push-wire,including the distance between nozzle and workpiece,wire feed cables of torch,using same size tip with wire,correct usage of soft wire feed tube,bending angle of gooseneck ,installation and uninstallation of gooseneck and inner soft wire feed tube.

对推丝式半自动CO2气体保护焊焊枪的使用与维护进行了详细的叙述，包括：喷嘴至工件间的距离大小，焊枪的送丝电缆，使用与焊丝尺寸一致的导电嘴，送丝软管的正确使用，鹅颈的旋转角度、装卸方法以及内送丝软管的装卸方法等。

Another rotary nozzle and the decline and refraction; Series faster then plastic pipe fittings; filter series products; absorption of fat, and fertilizer tank products; all kinds of specifications models of anti-aging PVC, PE pipe and fittings and so on.

另有旋转式和和折射式微喷头；系列快接塑料管件；过滤器系列产品；吸肥器、施肥罐系列产品；各种规格型号的抗老化PVC、PE管材及配件等。

This thesis focus on the research and development of water mist fire extinguishing system and its key component of swirl nozzle for the purpose of improving domestic development of the high-pressure water mist fire extinguishing technology.

因此本文对高压细水雾灭火技术及其关键元件离心式喷嘴的研究，对推动该技术在我国的发展和应用具有重要的意义。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48