查询词典 biasing circuit

The biasing circuit (6) dynamically biases the sensor (10) in response to a bias setting signal.

所述偏置电路(6)响应偏置设置信号动态地偏置所述传感器(10)。

The experimental results have shown that the impact of TFT threshold-voltage variation on the biasing circuit can be reduced from 30% to 5% under biasing voltage of 3 V.

因此，在第六章中，本论文提出具有临界电压补偿功能之偏压电路设计技术，此技术可以大幅降低元件的变动对偏压电路的影响，提高类比电路在玻璃基板上之可行性。

Improvement in the voltage dividing precision of a Photomultiplier Tube biasing circuit.

生命科学仪器中光电倍增管偏置电路分压精度的提高。

AIM: To analyze the influence of Photomultiplier Tube voltage biasing circuit on the performance of PMT, and to take corresponding measures for elevating the accuracy of PMT voltage biasing circuit accuracy to improve the performance of PMT.

目的：分析光电倍增管电压偏置电路对光电倍增管性能的影响，并采取相应措施提高光电倍增管电压偏置电路的精度，以改善光电倍增管的性能。

The processor (1) is operable to generate the bias setting signal (3) and thereb y control the biasing circuit (6) to dynamically bias the sensor such that the signal characteristic of the output signal is maintained in a target range.

所述处理器(1)可操作用于产生偏置设置信号(3)，由此控制偏置电路(6)以动态地偏置所述传感器(10)，从而所述输出信号的所述信号特征被保持在相对小的目标范围内。

On the other hand, the linear deviations of the active voltage biasing circuit with Bipolar Transistor or FET were at most 7%, and at most 3% respectively.

结果：在阳极电流为50 μA，电阻型光电倍增管偏置电路的线*偏离度已达40%，而用双极*晶体管或场效应晶体管的有源偏置电路的线*偏离度分别为≤7%，≤3%。

METHODS: On the basis of PMT passive voltage biasing circuit, Bipolar Transistor or Field Effect Transistor were used. Additionally,"adjustable constant current technology" was adopted to avoid the effect of temperature on circuit.

在电阻型光电路倍增管偏置电的基础上，增加双极型晶体管或场效应晶体管构成有源光电倍增管偏置电路；并采用可调恒流技术，以解决温度对电路的影响。

We simulate the circuit with the Agilent ADS, After select the most suitable topology structure of circuit,we simulate the biasing circuit,input and output matching circuit. Through the method of the small signal s parameters and the nonlinear designing method, we design and simulate the drive stage and last stage power amplifier with ADS software, point out some problem in the design procedure.

设计软件采用Agilent ADS软件进行仿真设计，在选定合适的拓扑结构后，对放大器的静态偏置点、输入输出匹配电路进行仿真，通过应用小信号S参数设计方法和非线性设计方法分别设计了驱动级和末级放大器，指出了设计过程中的一些问题。

If you jumper the 220 ohm, clip out the extra buffer transistor and connect the jfet signal coupling cap to the emitter of the input buffer, and change one resistor in the input buffer biasing circuit, you have a working TS9 in the TS10 case.

如果你跳了220欧姆，剪辑出额外的缓冲晶体管和连接场效应信号耦合帽来灌水的输入缓冲区改变一个电阻器的输入缓冲器偏置电路，你有一个工作ts9在ts10案件。

The sensitive amplifier has a circuit with simple structure, small occupied area, high read speed, low dynamic power, wide range of operation voltage and almost-zero static power and does not need a biasing circuit; the read circuit formed by the sensitive amplifier has the characteristics of anti-degradation of the properties of elements and stable performance.

该灵敏放大器电路结构简单，不需要偏置电路，占用面积小，读取速度快，动态功耗低，静态功耗几乎为0；工作电压范围大；由上述的灵敏放大器构成的读电路具有抗器件特性退化，性能稳定的特点。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。