查询词典 bevel gearing

Hoist traveling adopts NF series bevel wheel gearbox drive, drive wheel of both sides transfer torque through a 6-edge steel, large transferring torque, high reliability avoid invalidation of flat-key.

葫芦运行采用NF系列斜齿轮减速机驱动，两侧驱动轮通过一根六棱钢传递扭矩，传递扭矩大，可靠性高，避免了平键剪切失效的情况，并且此种传动还非常有利于葫芦运行部分的安装调节

Excellent three-in-one transmission technical, lifting gearbox applies high grade alloy section steel fabricated involute curve bevel wheel gearbox, 3-pole deceleration, smooth traveling, long life-span, reliable property, avoid many shortcomings of CD hoist intermediate shaft long distance transmission.

优良的三合一传动技术，起升减速机采用优质合金钢制造，三级减速，运行平稳、寿命长、性能可靠，避免了CD葫芦中间轴长距离传动的许多缺点。

The floor was of a reddish hue, waxed and polished, and in every direction were mirrors -- tall, brilliant, bevel-edged mirrors -- reflecting and re-reflecting forms, faces, and candelabra a score and a hundred times.

但是在这一刹那间看见的是另一个嘉莉--贫困、饥饿、走投无路，而整个芝加哥是一个冷酷、排外的世界，因为找不到工作，她只能在外面流浪。

Straight gear and hand chain of brake, eliminate worm gear cranes; straight gear and brake casting ladle will replace the worm and bevel gear casting ladle.

直齿轮加制动器的手拉葫芦，淘汰了蜗轮起重机；直齿轮加制动器的浇包，会取代蜗轮加伞齿轮的浇包。

Straight gear and hand chain of brake, eliminate worm gear cranes; straight gear and brake casting ladle will replace the worm and bevel gear casting ladle.

直齿轮加制动器的手拉葫芦，淘汰了蜗轮吊车；直齿轮加制动器的浇包，会取代蜗轮加伞齿轮的浇包。

Cigarette maker ; Spiral bevel gear ; Spacer ; Assembly jig ; Assembling ; Setting

卷烟机；弧齿锥齿轮；调整垫片；工装；装配；调整

For the groove part, at present, direct bevel cutting technology has been used in NC cutting machine in developed country. The mainly used function part is rotary cutting torch.

对于有坡口的零件，发达国家已经采用在数控切割机上直接切割坡口的技术，其采用的主要功能部件是回转割炬。

Both theoretical and experimental analyses on the natural frequencies and modes of the disk-shaped bevel gear are presented by using thick conical shell theory considering transverse shear d-eformation and rotational inertia, and using experimental modal analysis respectively.

本文介绍了用考虑横向剪切变形和转动惯性的厚锥形壳理论来分析盘形锥齿轮的振动固有频率和振型，并用试验模态分析技术进行测量。

Spiral bevel gear; gear honing; draft pattern interference; diamond dressing wheel

螺旋锥齿轮；珩齿；拔模干涉；金刚石修正轮

Detailed inventory of products: turning cutter: 45 degrees higher level of cutter, a 90-degree-angle-cutter, a round-cutter blade, discoid lateral cutter, drill cutter, side cutter, corn cutter blade, 45-degree bevel knives, T slot knife, ball-cutter, ball-cutter, and so on ......

可转位铣刀：45度台阶面铣刀、90度清角面铣刀、圆刃端铣刀、盘状侧铣刀、钻铣刀、端铣刀、玉米刃铣刀、45度倒角刀、T槽刀、球头铣刀、球头铣刀等等。。。。。。

Finally it offers the analysis of the fault-tolerance system as well as its test verification.

这样，运行于空间环境中的系统的设计目标就是在保证系统实时性

However, it is still difficult to find out the real reason of the increase of the keratinized gingiva during the orthodontic extrusion whether it is due to the proliferation of the gingival tissue or to its elastic nature, that is because the proliferation of the fibroblasts as well as the connective tissue changes in volume and the intra-fibers spaces were all immeasurable in most of the studies.

然而，仍然难以找到真正的原因增加的角化牙龈在正畸挤压它是否是由于扩散的牙龈组织或其弹性性质，这是因为增殖的成纤维细胞以及作为结缔组织的变化量和内部纤维空格都是不可估量的，大多数的研究。