查询词典 bevel gear

Loxodrome normal circular-arc spiral bevel gear transmission is a typical engineering application based on the principle of Betrand conjugate surface. It is likely to be the hi-tech prototype for the middle or large spiral bevel gear.

斜航式法向圆弧螺旋锥齿轮传动是贝特朗曲面原理指导下的一类典型工程实现，可望为中大型锥齿轮传动提供一种新技术原型。

The main products are CNC punch Tape feeder, NC spiral bevel gear milling machine, CNC spiral bevel gear tooth pull machines.

主要产品有数控冲床送料机、数控弧齿锥齿轮铣齿机、数控弧齿锥齿轮拉齿机等。

The most important feature of this design is: Lord reducer is not a conventional double-bevel gear surface, but a spiral bevel gear.

本设计的最大特点是：主减速器不是采用传统的双曲面锥齿轮，而是采用弧齿锥齿轮。

Bookbinder book bevel gear is a piece of steel angle and a bakelite bevel gear, drive out all of the roll out of the book.

胶订机出书伞齿轮是一件钢伞齿轮和一件胶木伞齿轮，传动出书的所有出书辊。

Right angle bevel gear reducer of the B series, concentric shaft bevel gear reducer of the H series, no paragraph series variable speed reducer.

直角斜齿轮减速机的B系列、同心轴伞齿轮减速机的H系列，无段变速减速机系列等。

First ,make up the main parts'structure and the key designing parameters; thus reference to the similar driving axle structure , decide the entire designing project ; fanially check the strength of the axle drive bevel pinion ,bevel gear wheel , the differentional planetary pinion, differential side gear , full-floating axle shaft and the banjo axle housing , and the life expection of carrier bearing .

本文首先确定主要部件的结构型式和主要设计参数；然后参考类似驱动桥的结构，确定出总体设计方案；最后对主，从动锥齿轮，差速器圆锥行星齿轮，半轴齿轮，全浮式半轴和整体式桥壳的强度进行校核以及对支承轴承进行了寿命校核。

The main structure of the bridge before the drive axle housing is cast steel or welded axle housing plus red spiral bevel gear reducer planetary wheel speed increases, round side down and between the spiral bevel gear reducer through the double-connected universal joints, the entire series has a wide range of speed than optional, the situation is widely used in a variety of off-road vehicle use.

斯太尔后驱动桥主要结构是冲焊桥壳加螺旋锥齿轮减速加轮边行呈减速，轮间差速带有差速锁，整个系列有多种速比可选。整车离地间隙大，通过性好，桥壳截面进行了强化设计，提高了实际承载能力。可选装ABS，但桥额定轴荷13000kg。该桥可广泛应用于各种公路运输车辆，特种车，越野车，客车。

In the general milling bevel gear with the casting process, the general use of bevel gear cutter, a two-blade or 3 blade into the teeth milling.

在普通铣床上用成型法加工伞齿时，一般都采用伞齿轮铣刀，以两刀法或三刀法将齿铣成。

To start off, we're going to look at the butt end of the racket handle. The handle has eight sides, also called "bevels," and the topmost bevel is Bevel 1. Bevels 2, 3, 4 etc. follow going clockwise around the handle. Bevel 5 is located on the "bottom" of the handle.

首先我们观察拍柄的平头端，拍柄有八面，也就是八个斜面，最上面的标记为1，然后顺时针方向是2，3，4等等，底5面试拍柄的最下面的一个面。

Derives the formulae for calculating the distortion and stress on the acting surface of flexspline load in the drive process of the harmonic gear drive with three-wave wavegenerator;(2) analyzes and compares the performance of plastic and steel products under light load drive and calculates the probably reached limit of drive ratio for both types of flexsplines under the same load;(3) applies the harmonic gear drive with three-wave wavegenerator to the small-sized multiple-revolution electric device of valves by taking into consideration of the low limit of the drive ratio for the harmonic gear drive with three-wave wavegenerator made of plastics, improves the design on the main drive mechanism of the traditional small-sized multiple-revolution electric device of valves, and validates through examples the feasibility for the harmonic gear drive with three-wave wavegenerator made of plastics to be applied to the small-sized multiple-revolution electric device of valves. Finally the author performs calculations on the two types of the flexsplines of the harmonic gear with three-wave wavegenerator by using the finite element method and analyzes the causes for the errors.

本文根据三波谐波齿轮传动的运动变形特点，采用弹性薄壳的力矩理论，推导了三波谐波齿轮传动柔轮载荷作用面上的变形及应力计算公式；分析比较了轻载传动情况下塑料和钢材的性能，计算了塑料制谐波柔轮和钢制谐波柔轮在相同载荷情况下可能达到的传动比极限；对塑料制及钢制三波谐波齿轮柔轮进行了有限元计算，分析了产生误差的原因；针对三波塑料谐波齿轮传动比极限低的特点，将之运用于小转矩多回转阀门电动装置中，对传统的小型多回转阀门电动装置的主传动机构进行了改良设计，并通过实例验证了三波塑料谐波齿轮传动在小转矩多回转阀门电动装置中应用的可行性。

You have to walk your own alk in this life.

次生中你必须走自己的路。

To start with, the thesis analyses ***ism in terms of the generic masculine words, word order and semantic derogation of women in greater detail.

论文首先从阳性词泛指，词序，词义的贬降等方面对英语中的性别歧视现象进行了详细的分析。