查询词典 bevel gear

A method of double third -power spline is used to add more nodes to the surface of a spiral bevel gear .

提出了一种用位移矩阵法精确求解实现四个或五个位置的刚体导引机构的综合，实现了两边架杆四个或五个对应位置的函数机构的综合以及其它一类连杆机构综合的方法。

In addition, the spiral bevel gear reducer single-stage main bridge increased after the transmission efficiency, improved transmission reliability.

并且，弧齿锥齿轮的单级主减速器提高了后桥的传动效率，提高了传动的可靠性。

Above result revealed that multidirectional closed die forging of spiral bevel gear was feasible.

揭示了使用复动闭式模锻模具成形小锥角螺旋伞齿轮的可行性。

There is an obvious disparity between our nation and other developed nations in the field of hard surface finish machining of the spiral bevel gear.

在螺旋锥齿轮硬齿面精加工这一环节上，我国与发达国家的差距尤为明显。

It analyses the influence of support stiffness on critical speed and unbalance response and vibration characteristics of the spiral bevel gear train system.

讨论了支承刚度对系统临界转速及不平衡响应等振动特性的影响，得出一些规律性结论，用以指导齿轮传动系统的设计。

On the basis of studying PECF's basic laws, many experiments are carried out on the 20CrMnTi which has the identical material with spiral bevel gear.

本文在深入了解脉冲电化学光整加工工艺的基础上，对具有与螺旋锥齿轮相同材料(20CrMnTi)的试件进行了大量的实验研究。

On the basis of the model, the friction force in each meshing point on the spiral bevel gear surface covered by silver film is presented by numerical method. In addition, the result is indirectly proved by experiment.

用数值法求解了弧齿锥齿轮镀银齿面之间各啮合点处的摩擦系数；以试验方法对数学模型的正确性进行了间接验证；通过详尽的数值计算探讨了银层厚度、刀盘直径、基体硬度等参数对摩擦系数的影响。

The procedures used mathmatics establishment, used to complete the spiral bevel gear surface and quasi-two-tooth surface of the geometric design.

该程序用mathmatics编制，用来完成弧齿锥齿面和准双曲面齿面的几何设计。

The accurate measurement of the structure parameters of real tooth surface of spiral bevel gear with the coordinate measuring machine is the key to evaluate the geometric quality of the real tooth surface quantificationally, and the base of machine-settings correction.

在三坐标测量机上精确测量螺旋锥齿轮真实齿面的结构参数是定量评价其齿面几何质量的关键，是齿轮加工机床参数修正的基础。

Using two-flank-staining method, inspect the tooth flanks of the driven bevel gear, 3 to 4 equispaced spots along the circumference, at each spot apply color to 2 to 3 teeth, the correct meshing print requirements are: print width in the direction of face width not less than 50% to 60% of the facewidth , and that in the direction of tooth depth not less than 40% to 50% of the tooth depth.

用两面着色法，在从动锥齿轮的齿面检查，沿圆周均布3-4处，每处2-3齿涂色，正确啮合印迹要求为：在齿宽方向的印痕宽度不小于齿宽的50%---60%，在齿高方向的印痕宽度不小于齿高的40%---50%。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了