查询词典 bending
- 与 bending 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Using CHAMP observational data samples, the profiles of atmospheric bending, refractivity, pressure, and temperature were retrieved in turn by the series of signal noise ratio.
利用CHAMP卫星的GPS掩星观测资料,通过观测信噪比序列进行了大气弯曲角、大气折射率、大气压、温度剖面的反演计算;并与相位反演结果进行了比较和讨论。
-
Using the characteristic of the regular curve boundary for a bending plate in engineering,the analytic integral formulae of assistant states in boundary element method with the linear element for a Kirchhoff circular plate are introduced and the systematic equation of BEM is established in this paper.
利用一般弯曲薄板边界为规则曲线的特点,对工程常用的圆形弯曲薄板,采用线性单元,导出K irchhoff圆板各辅助态的边界积分解析表达式,建立问题的边界元法系统方程,从而使薄板的边界元分析完全避免通常使用的高斯积分,明显提高计算精度。
-
By employing a new pattern of combination, in which the analytic method is the basis and the numeric method is the reinforcer, the composite Fourier series method is proposed in the thin plate bending problem.
提出薄板弯曲问题的复合傅里叶级数方法。它以解析方法为融合基体,数值方法为融合增强相,是一种新的融合模式。
-
The main contents and achievements are summarized as following: 1. The principle of tension leveling of metal strip is described systematically using relative tension and relative curvature on the basis of plane hypothesis including the stress distribution on the section, the condition to undergo plastic longitudinal elongation, the calculation of longitudinal elongation, the change of tension along the strip etc.. 2. The tension leveling process of metal strip on a multi-roll arrangement is investigated detailed by nonlinear finite element method and many rules to guide the strain, deformation, stress and bending moment are discovered and illustrated.
本文的主要内容和成果如下: 1、以平面假设为前提,采用解析分析方法,建立了以相对张力和相对弯曲曲率为基本参数的平面应变金属带材拉伸弯曲变形基本原理较为系统的描述,描述涉及到应力分布与两个基本参数的关系、带材塑性延伸的边界条件、带材延伸率的计算、带材张力变化的计算等。
-
The formula of the minimum relative bending-radius, which is related to mechanical property of the tube and constrained by tensile destabilizing, is concluded...
给出与管材力学性能相关,且受拉伸失稳约束的最小相对弯曲半径的计算公式,可用于工艺计算,并对管材弯曲成形设计和工艺分析具有一定的参考价值。
-
The remotion of neutral axis and flat-section assumption were proved through the bending test of plain concrete .
1 混凝土弯曲变形中的几点假设混凝土从加载到出现宏观裂纹这一过程中,做以下几点假设:①平截面假设仍然成立。
-
Based on complex transfer matrix method,a model to calculate unbalance response of a residual bending rotor is set up.Response of different residual bend mode is analyzed.
0前言转子由于加工误差以及热变形等众多因素的影响,经常会产生一定的弯曲量,引起转子振动。
-
In this paper,the method of weighted residuals is employed to analyze the bending problems of anisotropic skew plates.
近几年对各向同性斜交板的横向弯曲问题有过不少的分析方法仁,一'〕。
-
Occurrences of septate internodes can improve the ability of resist bending, while this improvement depends on the internodes' position and distance.
在计算中,建议将截面屈曲程度达到25%作为茎发生屈曲的标准; 3、茎节的出现能够增加茎抵抗弯曲的能力,增加的具体程度与茎节出现的位置,节距有关。
-
In accordance with the needs of solving problems, mold experiments carried out are as follows:(1) Testing flexural normal stress, shearing stress and shearing force stagnant effect of molds of organic glass and load's lateral distribution coefficient of beam's ribs;(2) Testing rigid torsion and distortion effect of molds of organic glass;(3) Testing cap plates' vertical and lateral efficient load working breadth of molds of organic glass;(4) Testing lateral frame's bending moment of molds of organic glass within the range of their working breadth;(5) Experiment on respondency of dynamic force of molds of organic glass.
根据解决问题的需要,所作的模型试验有:⑴测试有机玻璃模型的弯曲正应力、剪应力、剪力滞效应和箱梁梁肋荷载横向分布系数;⑵测试有机玻璃模型的刚性扭转和畸变效应;⑶测试有机玻璃模型顶板纵向、横向荷载有效工作宽度;⑷测试有机玻璃模型载荷在工作宽度范围内的横向框架弯矩;⑸有机玻璃模型的动力响应试验。
- 推荐网络例句
-
Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.
Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。
-
I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.
我来只是现在,'歼灭战perfuming自己与胡努特,那麼,他来到和SAT 。
-
The shamrock is the symbol of Ireland and of St.
三叶草是爱尔兰和圣特里克节的标志同时它的寓意是带来幸运。3片心形叶子围绕着一根断茎,深绿色。