查询词典 bending

Thus, the change only results in adjustments to the equivalent point loads at A and B and to the equivalent loading near B. As these forces are at or near supports, they do not significantly affect the distribution of bending moment induced by prestress.

因此，唯一的变化调整的结果相当于点负载在A和B以及相当于载入中附近湾由于这些部队正在达到或接近支持，他们不显着影响的分布弯矩诱导预应力。

So we conclude that the bending of light that we found in the accelerated system does indeed apply equivalently to a gravitational field.

所以，我们断定，我们在加速系统里面发现的光线的弯曲确实和一个重力场中的相等价。

At last, the error curve surface of gear profile is obtained by combining bending deformation and contact deformation.

文中首先将刀齿和轮齿抽象简化为力学模型，分析其受力状态，并运用三维有限单元法计算各节点的弯曲变形量，建立切削力与弯曲变形的关系。

Punching technology for the sleeve of a new type expansion bolt;2. Ultimate strength of sleeve reinforced T-joints under out-plane bending;3. Various defects may occur in the production of plastic sleeve of railway switch tie with non-alkali glass fiber reinforced polyamide 66(GFRPA66), and reasons caused these defects are analyzed.

采用玻璃纤维增强尼龙66(GFRPA66)为原材料生产铁路岔枕套管时经常出现各种制品缺陷，分析了这些缺陷产生的原因，提出了通过调整成型工艺条件(注射温度、注塑压力、注射时间等)、改进模具结构及对原料进行预干燥处理等解决措施。

The bending problems of composite shells of revolution subject to various loading condition are solved by the finite element method and Fourier series expansion in this paper.

本文用有限元法和Fourier级数展开技术求解复合材料回转壳体在各种荷载作用下的弯曲问题。

Keywords: Electronic extensometer; Eccentric tension; Elimination of bending effect; Pure tensile elongation

下面用图2所示的偏心拉伸模型来计算单侧电子引伸计的测量误差。

Under the loading of internal pressure or in-plane bending moment, the plastic load analysis solutions of pipe bends with longitudinal crack on bend crown, intrados or extrados are studied and verified by experiments.

系统地研究了在内压或平面内弯矩作用下处于几何中性线，内、外拱线的弯管纵向裂纹塑性极限载荷的解析解，实验验证了本文分析是正确的。

The method provides preparation with metal pattern the candle of same size 96, the false tooth that 2 kinds of brands use after breaking candle base hold colophony in the palm to fill glue, undertake with 4 kinds of methods heat treatment makes its solidify, detect with machine of all-purpose and mechanical experiment base hold resinous bending intensity in the palm, mix with double element variance analysis multiple undertake statistical processing quite.

方法用金属模具制备相同尺寸的蜡型96个，失蜡后使用2种品牌的义齿基托树脂填胶，用4种方法进行热处理使其固化，用万能力学实验机检测基托树脂的挠曲强度，用双因素方差分析和多重比较进行统计学处理。

The wheel's felloe rigidity, natural frequency and the spoke bending stress was taken into consideration in this thesis to carry outthe optimization design of a 17 inch wheel, more reasonable structural parameter of the wheel was obtained.

建立了综合考虑车轮轮辋刚度、车轮模态和车轮弯曲疲劳寿命的影响的一个17英寸车轮结构优化设计模型，并在此基础上对该车轮进行了优化设计，得出了更加合理的车轮结构参数。

Subsequently, on the basis of simplifying the structure and boundary condition, the FEM models of the wheel's felloe rigidity computing, the wheel modal computing and the wheel bending analysis were built separately.

而后在对结构、边界条件简化的基础上，分别建立了车轮轮辋刚度计算、车轮模态计算和车轮弯曲分析有限元模型。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。