查询词典 bending

The effect of densification and different heat treatment ways on bending strength and coefficient of thermal expansion of SiC/Al composite was studied.

研究了致密度及不同热处理状态对SiC/Al复合材料的抗弯强度和热膨胀系数的影响。

Cold frame bending machine with multiplungers|n.

多压头式肋骨冷弯机

In the dissertation, the nonlinear bending of circular sandwich plates based on Reissner theory is analyzedThe method of Point Collocation are used in the calculation,with the B-spline function taken as the trial function.

本课题研究了基于Reissner理论的夹层圆板的非线性弯曲问题。文中采用配点法计算，以三次样条函数作为应力函数和挠度函数的试函数。

A method for compensating residual bending rotor is put forward based on theoretical analysis.A 100MW Turbo-generator is used as an example.

目前有关初始弯曲转子振动的研究大多是针对单圆盘转子模型[1，2]，这类模型过于简单。

By means of bending tests of three-point and four-point, complex fracture experiment s were made for cast iron material with crack.

通过3点弯曲和4点弯曲实验方法，对含有裂纹的铸铁材料进行复合型断裂实验研究，测试铸铁材料的应力强度因子、断裂方向角，将实验结果与理论值进行分析、比较，找出两者之间的异同点，得到一些对工程设计及应用具有实际意义的结论。

An experimental formula of bending loss is suggested on the basis of conformal transformation and normalized approach used in analysis of curved optical waveguides.

介绍了分析波导弯曲损耗的保形变换法和归一化方法以及由此得到的波导弯曲半径与弯曲损耗的关系式。

An inside conical surface at the lower end of the joint is designed to ensure the shaft swing freely within an angle range of 10°, thereby the axial bending stress caused by the deflection of the borehole can be eliminated effectively.

这种装置采用类似球形关节的旋转机构，消除了抽油杆柱上下往复运动产生的倒扣扭矩；在短节下端设计有10°的内圆锥表面，使转轴能够在10°范围内自由转动，从而有效地消除了由于井身弯曲而产生的轴向弯曲应力。

And it was divided into four groups at randomly (n=6),The vertical compression,bending and torsion intensity in without and with reduction of cortical fragment of plate fixated contra side, without and with reduction of cortical fragment of plate fixated sidewere measured.A11 results were analyzed with statistic method.2、animal experiment :The 12 adult goats were divided into two group at randomly,wedged cortical defect with 1 cm of long and conjugate diameter was created in the middle-part of the medial femur and plate was fixed in the defect side and as the experimental side,the other side was control.after operation 4、8、12 weeks,investigation of the fracture healing by means of gross observation,X-ray examination and histology in both sides.

测试各组的垂直压缩、三点弯曲及抗扭转的刚度。2、动物实验：12只健康成年山羊，雌雄不限，体重在20～25kg之间，在同一只羊双侧股骨中段内侧制造楔形骨皮质缺损，分实验组和对照组两组进行钢板内固定并植骨，于术后4、8、12周对实验组及对照组行X线正位片检查，观察骨折愈合过程中不同时间点的影像学特点。于4、8、12周各组处死4只动物行大体标本观察，并取缺损区骨组织行组织学检查。X线检查及组织学检查结果根据LaneX线评分标准及组织学评分标准进行评分。最后采用SPSS13.0进行统计学分析。

In the bending rig the reaction force of the reel on the pipe was not constant in value.

在弯曲的反应部队钻机的辘的管道（ Freel ；慧聪；规划）不恒定的价值。

In the contact force of facet joint, the maximum increase reached 10% in lateral bending mode.

临床病例分析结果指出椎足螺钉断裂发生在下方有12人，断裂在上方位置有4人。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。