查询词典 bending

The results show that the amorphous PLGA fiber with porous structure (0.1-1.0 μm) is obtained by diluted solvent spinning method and the mechanical properties is affected by pressure and temperature. Bending strength and shearing strength of the samples increase firstly and then decrease with the increase of molding temperature and pressure. While the molding temperature is 160℃and the pressure is 105MPa, the PLGA materials possess optimal mechanical properties, bending strength, shearing strength and bending modulus 187.3 MPa, 100.0 MPa and 2.5 GPa, respectively. The mild temperature molding PLGA materials are desired to play a grate role in non-bearing internal fixation devices.

研究结果表明：非晶多孔结构的PLGA纤维可通过溶液沉析纺丝的方法获得，其孔径为0.1~1.0μm；压制压力和压制温度对材料的力学性能影响较大，材料的抗弯强度、剪切强度和抗弯模量均随着温度和压力的增大而先增大后降低；在压制压力为105MPa，压制温度为160℃时，试样的力学性能比较理想，此时，其抗弯强度可达到187.3MPa，剪切强度达到100.1MPa，抗弯模量达到2.5GPa，可望作为非承重部位骨折愈合内固定材料。

On the analogy between plane elasticity and plate bending theory, moment functions of plate bending in polar coordinates are introduced as original variables to establish a symplectic space in circumferential direction for the bending of annular sector plate with an appropriate definition of symplectic inner product.

根据平面弹性与薄板弯曲问题的相似性原理，极坐标系板弯曲的弯矩函数被引入作为原变量，并通过恰当的辛内积定义建立了环扇形薄板弯曲问题的一个辛几何空间。

Choice of materials for Q235, The choice program is stamping process Piercing blanking -- thinning Burring -- Wedge-bending -- U-shaped curve In this program of cost savings but also appropriate to increase production efficiency, use of this program will mainly involve the following four die : Punching blanking die;(2) thinning Burring die;(3) Wedge-bending modulus;(4) U-bending modulus.

选择的材料为Q235，选择的冲压工艺方案是冲孔落料--变薄翻孔--斜楔式弯曲--U型弯曲，此方案在节约成本的同时也适当的提高了生产的效率，采用此方案将主要涉及到以下四套冲压模具：（1）冲孔落料模；(2)变薄翻孔模；(3)斜楔式弯曲模；(4)U型弯曲模。

The results show that increasing the ball numbers and mandrel extension length may reduce the ovalization, but leads to more remarkable wall thinning; the ovalization becomes more severe with the larger bending angle; the smaller the relative bending radius, the larger the ovalization is; the ovalization and wall thinning degrees are both smaller in the case of pressure die with dry lubricant; and under the same bending condition, the ovalization of LF2M tube is larger than the one of 1Cr18Ni9Ti tube.

结果表明，增加芯头个数与芯棒伸长量都能减小弯管的截面畸变，但两者都导致弯管壁厚减薄量增大；随着弯曲角度的增加，截面畸变越严重，相对弯曲半径越小，无芯棒与芯头支撑段弯管的截面畸变愈严重；在压块无润滑情况下，弯管的截面畸变和壁厚减薄量都小，并且在同等弯曲条件下，1Cr18Ni9Ti弯管的截面畸变小于LF2M弯管。

It is indicated that, the bending curve is not asymmetrical and there will not have moment of flexure on the top of the bending section. Based on a slantwise constant-thick beam which foot is fixed, and took deadweight of bending section to account, a theoretical differential equation of third order for buckling equilibrium state was established.

在分析了顺层斜坡地质原型变形形态的基础上，由考虑自重的阻滑端固定的斜置等厚弹性板梁模型，提出了以地质原型变形形态抽象出相应边界条件的分析方法，及理论上求解挠曲线的适定三阶微分方程。

Priced Direct: Shearing Machine, Bending Machine, Punching Machine, Three Roller Bending Machine, Hydraulic Press, four columns, bending machine, leveling machine, processing machine scheduling bus motor, blade shears, press brake tooling, forging, etc. gold plate, machinery and machine tool attachment.

厂价直销：剪板机﹑折弯机﹑冲床﹑三辊卷板机﹑四拄液压机﹑弯管机﹑校平机﹑母线排加工机﹑电动机﹑剪板机刀片﹑折弯机模具﹑等锻压﹑扳金机械及机床附件。

On the scale of punch and die with punching and bending die punch; Die positioning pulled positioning and bending Die top two pieces of equipment; 6 punch with epoxy fixed on the next model, since blanking punch and bending die role.

上模为凸凹模起冲裁凹模和弯曲凸模作用；模具中定位板起定位和弯曲凹模顶件装置两种作用；六个凸模用环氧树脂浇注固定在下模上，起冲裁凸模和弯曲凹模作用。

The PBS330A series Bending Machine was launched in 2006. It's a new type computer automatic bending machine that can punch bridges while bending. The punching design is so simple that we can change moulds in only three minutes. This series of machines are well reputed since launch.

PBS330A系列弯刀机是沃迪刀模设备2006年推出的新型弯刀机，能在弯刀的同时完成打桥位的工序，其桥位设计简易，只需三分钟，即可更换模具，省时省力，自推出以来，好评如潮。

Workpieces as concave bending, convex bendingS bending can be achieved by bending to the shaping material, straighteningleveling of the shaping material are also available.

通过对型材进行弯曲，可获得平整内弯、外弯、S弯形状的工件，也可进行型材的校址和校平等特点。

We can also provide special purpose of bending die, elbow-, knife-shaped die, 90 °, 60 °, 45 °, 30 °, R-shaped, cylindrical, pressure-bending, U-bending and embossing Die, Die container, various Denggan mode, cutting plate machine blade, to map processing, non-standard design.

我们还可以提供特殊用途的折弯模具，有弯头模、刀形模、90°、60°、45°、30°、R形、圆柱形、折弯压力形、U型和折弯压印模、集装箱专用模、各种灯杆模、剪板机刀片、来图加工、非标设计等。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。