查询词典 bending point

The main mechanical properties in warp and weft direction of the hollow integrated core sandwich composites are obtained by edgewise tensile, edgewise compression, flatwise tensile, flatwise compression, double lap shear, and four point bending experiments. Some properties are compared with the honeycomb sandwich composites.

对整体中空夹层复合材料经、纬向的侧拉、侧压、平拉、平压、双层剪切和4点弯曲等性能进行了实验研究，获得了该种材料的主要力学性能参数，并与类似的蜂窝夹层材料部分力学性能进行了对比。

The main mechanical properties in warp and weft direction of the hollow integrated core sandwich composites are obtained by edgewise tensile,edgewise compression,flatwise tensile,flatwise compression,double lap shear,and four point bending experiments.

对整体中空夹层复合材料经、纬向的侧拉、侧压、平拉、平压、双层剪切和4点弯曲等性能进行了实验研究，获得了该种材料的主要力学性能参数，并与类似的蜂窝夹层材料部分力学性能进行了对比。

Secondly, the paper carries on the destruction processes and the stress distribution situation numerical simulation of the concrete three point bending specimen with bias crack under static load function,, and analyze specimen crack expansion and the destruction mechanism, obtain the reason that the crack expanding flectional way is because the material nonuniformity, in the same time, from the specimen destruction process chart we can see that the crack bias degree has some influence on the crack expansion way.

其次论文对含偏置裂纹的混凝土三点弯曲试件在静态载荷作用下的破坏过程和应力分布情况进行了数值模拟，并对试件的裂纹扩展和破坏机理进行了分析，得出裂纹扩展的曲折性是由于材料不均匀性所引起的，同时从试件的破坏过程图中可以看出，裂纹的偏置程度对裂纹的扩展路径有一定的影响。

The generable proximate formula of dynamic stress intercity factor of simple edge crack found bar specimen in three point bending of NanLing marble is gotten and the critical dynamic stress intensity factor of the specimen is also obtained in medium load ratio.

在中等加载速率下，推导出对大理岩带垂直切口三点弯曲圆棒梁试件动应力强度因子的一般近似公式和断裂时的临界动应力强度因子的表达式。

In 3-point bending test, there was no difference between three groups. Part 2: Histomorphologically, the connectivity in group A was higher than that in control groups.

第二部分：组织形态学观察发现，bBMP/FS组骨小梁连接性明显优于对照组，形态较为规则，小梁间连接程度优于对照组。

By the way of X-ray stress measurement, the characteristics of residual stress distribution of specimens, which were shot peened and polished, were studied; by the way of three-point bending fatigue tests, the influence of polishing after shot peening on fatigue properties was studied; on this basis, the reason why Shot Peening Standards provide that the depth of metal removal does not exceed 10% of the specified arc height was analysed.

文中指出300M钢喷丸强化工艺中打磨对喷丸效果的影响问题；通过X射线应力测定，研究喷丸及打磨后试样的残余应力分布及变化的特点；通过三点弯曲疲劳试验，研究喷丸后打磨对试样疲劳性能的影响；在此基础上，分析喷丸标准中规定喷丸后打磨去除量不可以超过阿尔门强度值的1/10的原因。

The basis of static, flat汇交system of forces, torque and couple Department of plane, plane general system of forces, center of gravity and centroid, the internal force and internal force diagram, tension and compression, torsion, bending, stress analysis and strength of the theory of the stability bar , the point of movement, the basic rigid-body movement, points of complex, rigid body planar motion, the movement of particle differential equations, dynamic general theorem, static and dynamic method.

静力学基础、平面汇交力系、力矩与平面力偶系、平面一般力系、重心和形心、内力和内力图、拉伸和压缩、扭转、弯曲、应力状态分析和强度理论、压杆的稳定性、点的运动、刚体的基本运动、点的复合运动、刚体的平面运动、质点的运动微分方程、动力学普遍定理、动静法。

The data of flexural strength of the base plate materials were tested with three-point bending test.

用三点弯曲试验测试材料的挠曲强度，采用SAS6.12软件包对结果进行单因素方差分析。

Structurally its products can be divided into single-point,shear beam-bending,damped and column and etc.,weighing capacity ranges from 300 grams to 100 tons.

按结构主要分为单点式、剪切梁式、阻尼式和柱式等，量程从300克至100吨。

Now has casting, machining, finishing, flat-panel and other refinements of the workshop, the main products are cast iron flat-panel, flat line, the assembly of flat, square box, V-Rail, V-plane, parallel flat foot, the bridge-ping feet square, feet, machine-specific point of foot, bending plate, ladder Sizing Block, contour Sizing Block, migraine pendulum tester, gear beating device, machine tool inspection wand Adjustable Sizing Block Machine, Machine Tool Sizing Block shockproof, special wrench , explosion-proof tools, such as on-arc model; granite platform, flat feet, feet, square box, V-blocks, granite, table, Block, measuring instrument, such as granite.

现在有铸造、机加工、精加工、精研平板等车间，主要产品有铸铁平板、划线平板、装配平板、方箱、V型铁、V型架、平行平尺、桥型平尺、直角尺、方尺、机床专用角度尺、弯板、阶梯垫铁、等高垫铁、偏摆检查仪、齿轮跳动仪、机床检验棒、机床可调垫铁、机床防震垫铁、特种扳手、防爆工具、对弧样板等；花岗石平台、平尺、方尺、方箱、V型块、花岗石表座、花岗石测量仪等。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。