查询词典 bending point

"Three point bending experiments" were conducted to study the mechanical properties of sugarcane under bending load.

以"桂林—1号"甘蔗为试验材料，在日本SHIMADZU公司生产的AG-I50AUTOGRAPH材料力学试验机上进行了蔗茎的弯曲试验。

A molded bar of molding compound resistance to bending, tested using a 3 point bending test.

塑封料塑封后的小棒，用3点弯曲测试抗弯曲的强度。

It is found that two shear modulus are different and two shear strength are almost equal. The reason of differences between three point bending modulus and four point bending modulus is also analyzed.

在剪切试验中发现两种剪切试验的剪切模量相差较大，但由于两种剪切的破坏面相同，所以剪切强度相差不大。

The bending of rectangular plate is divided into the generalized statically determinate bending and the generalized statically indeterminate bending based on the analysis of the completeness of calculating condition at the corner point.

在分析角点求解条件完备性的基础上将矩形板弯曲划分为广义静定问题和广义超静定问题。

The bending of rectangular plate is divided into the generalized statically determinate bending and the generalized statically indeterminate bending based on the analysis of the completeness of calculating condition at the corner point. The former can be solved directly by the equilibrium differential equation and the boundary conditions of four edges of the plate.

在分析角点求解条件完备性的基础上将矩形板弯曲划分为广义静定问题和广义超静定问题，广义静定弯曲可以由板的平衡微分方程及四边边界条件直接求解，广义超静定弯曲可以由叠加法求解。

The paper carries out mechanical analysis of the weight distributing of goods in loading container based on analysis of packing and tansporting environment, and draws the formula of the ratio of the weight of loading goods and the maximum loading weight W/W0, and the length distributing ratio of loading goods α=l/L under the condition that the bending quadrature produced by part load is within the range of the maximum bending quadrature. It also gives the graph that the sum deflection of mudsill and underside girder can reach high-point value with the length of bottom distributing varying, when the loading amounts of container of 20ft and 40ft are given. Furthermore, it provides the relation graph of an eccentric rate of loading goods and the allowed loading amount. For on-site safety loading work, it has certain guidance and reference value.

在分析包装件运输环境的基础上，对装载集装箱的货物重量分布进行了力学分析，得出局部负荷产生的弯矩如在最大容许弯矩范围以内时，装载货物重量与最大载货重量之比W/W0，同装载货物的长度分布率α=l/L的关系式；绘出了20 ft和40 ft集装箱在装货量一定时，随着货物底分布长度的变化，底梁和下侧梁之合计挠度达到极限值的曲线图；绘出了装载货物的偏心率与容许装货重量的关系图；对现场安全装载作业有一定的指导作用和参考价值。

The model was validated by simulating the tibia three-point bending test and lower extremity sheering and bending tests.

本文中采用了LS-DYNA仿真软件，在已有的行人下肢模型(HBM-lower limb)的基础上进行了改进。

Presenting the calculating method of the space displacement model of skewed box girder, whit main ideas of: dispersing the skewed box girder into some skewed beam segments and further dividing those segments into some plate pieces according to their forms; describing the displacement functions in the plane of plate piece by assuming that the space displacements of any point in the joint line between the plate pieces are described by using Hermite interpolation functions and that two displacements in the plane of plate piece are linear in the cross direction; Using Hermite interpolation functions to describe the bending the displacement of the unit length transverse frame cutting longitudinal from the skew box girder segment; Finally, describing the space displacements of a point in the plate pieces by two displacements in the plane of the plate and one bending displacement of plate.

提出了斜交箱形梁空间位移场的计算方法：将斜交箱形梁沿纵向离散为若干斜梁段单元，依据箱梁的构成进一步将斜梁段划分为若干板段子单元；各板段联结线上任意点的位移按Hermite函数插值，假定各板段的面内位移沿其宽度方向线性变化，以描述各板段面内位移；沿斜交箱梁段的纵向截取单位长度横截面框架，框架各杆件空间位移按Hermite函数插值，以描述各板段面外位移；板段内任意点的空间位移最终以2个面内位移和1个面外位移描述。

The companys main products are: high school at the end of light-bending machines, at the end of high school material for hydraulic cutting machine, heavy thick material knife-bending machines, materials removed knife-thick, thick knife expected wheel machine, a tooth-and small point cut Knife machine, paint boxes, hand shear pressure feeder, cosmetic Taiwan, knife rack-first class professional products, according to customer requirements and design the appropriate professional products.

本公司主要产品有：高中底轻型弯模机、高中底档油压剪料机、重型厚刀料弯模机、厚刀料磨平机、厚刀料砂轮机、打牙机、点小切刀机、油漆箱、手压剪料机、整型台、刀料架模头等专业产品，并可根据客户要求设计相应的专业产品。

Therefore, the so-called three-point bending experiment is in fact the one-point bending experiment.

因此，所谓Hopkinson杆三点弯曲试验实际上是单点弯曲试验。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。