查询词典 bearing seat

The spherical center of the self-aligning seat must coincide with that of the self-aligning ball bearing.

球面中心的自我调整的席位必须配合，在自调心球轴承。

It is a self-lubricating material used as a seat and/or bearing material in most Chemtrol valves.

这是一种自润滑材料，在大多数Chemtrol阀门中用作阀座和/或轴承材料。

Install shaft snap ring in groove on shaft.Seat bearing against snap ring.

将轴卡环装到轴槽上，把轴承紧靠在卡环上。

4 Components in the guide ring seat surface, and to maintain stem vertically in a clean work surface; 4.5 Lubrication and installed on top of the spring washer bearings and bearing connecting rings, and lubricating the bottom of the spring washers, valve cover and gasket components will be placed in position inside the valve cover; 4.6 will regulate the bolt lock nut bolt screw to adjust the top.

4.4 将组件座于导环面上，并保持阀杆垂直地处于清洁的工作面上； 4.5 润滑并在顶部弹簧垫圈上安装轴承和轴承连接环，和润滑底部弹簧垫圈，将阀盖及垫圈组件放在阀盖内的位置上； 4.6 将调节螺栓锁紧螺母拧到调节螺栓的顶部。

The article with slipping seat of bearing as the three-dimensional modelling instance,discusses the varying law of system of coordinates and modelling aline...

文章以滑动轴承座为三维造型实例，讨论了构造复杂三维模型的变换坐标系法和造型对齐法。

The operation of the shaft and the sliding friction between the axle seat into a rolling friction, thus reducing the friction loss of a precision mechanical components, called the rolling bearing.

将运转的轴与轴座之间的滑动摩擦变为滚动摩擦，从而减少摩擦损失的一种精密的机械元件，叫滚动轴承。

Bearing outer ring or the outer surface of the seat ring.

滚动轴承外圈或座圈的外表面。

The main series products cover three aspects such as driven gears of motorbikes, electronikc power dual pinion wheels, automobile chain wheels, pulley wheels, valve guide, seat bush, signal wheels, disc, and bearing covers, electrical rear driven bridge powder metallurgical wheel and speed different gears. The parts also cover series for clutch plates for trains and automobiles air conditioning compressors as well.

产品系列包括：摩托车从动齿轮、电起动双联齿轮系列；汽车发动机链轮、皮带轮及气门导管、座圈、信号轮、相位盘、轴承盖系列；电动车后驱动桥粉末冶金大齿轮及差速伞齿轮系列；火车、汽车用离合器面片、空调压缩机粉末冶金零件系列。

Following testing and soon after commissioning of a system, if either the Model-B or Model-C valve develops a leak at the top bearing, the flange face-seal, and/or across the valve disk, the most likely suspicion would be inappropriate selection of the elastomeric seat and seals.

在系统测试和试运转后不久，如果型号B或型号C阀门的任何一种在阀门的顶部轴承、法兰面密封，以及阀门阀瓣等部分出现了泄漏，则很有可能是由于选择了错误的弹性材料阀座和密封。

After extended operation, if leakage should occur at the top bearing or across the valve disk of either the Model-B or Model-C valve, this is an indication of wear to the elastomeric seat and/or O-ring seals, requiring their replacement. In most cases, valve replacement will be found less expensive than parts replacement.

在进行操作后，如果泄露出现在型号B或型号C阀门的顶部轴承或阀门阀瓣上，则表明弹性材料阀座和/或O形环密封出现磨损，这时就需要进行更换。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。