查询词典 bearing seat

The bearing part is like fish back instead customary shaft seat and can weigh different shaft load; Using fish back shaped arc surface for bearing load can overcome error brought by shaft bend and horizontal deviation.

承载部位呈鱼背状，取代原来的轴座，可进行各种轴负荷的称重；鱼背状承载弧面可克服轴受载弯曲或安装水平偏差引起的称重误差；改变弧径尺寸可适应不同轴径。

Electric remote control device adjustment is used, General monlchamus tuhung seat mounted above the keybed-iron plate, covering a hard plastic, and a flexible plastic to prevent ink seepage, each iron plate is fitted with a front end, eccentric roller roller bearing rings on both sides of the plastic top tight in tuhung roll, bucket seat is fitted with a total of 30 to 32 of these eccentric roll, each of which the width of the eccentric roll and 30 ~ 32 mm, when servo motor signal receiving console by mechanical structure, change the eccentric roller and rollers of the gap, so that once the monlchamus tuhung-high ink, led, according to the extruded plastic clearance form different deposit, attachthemselves in tuhung roll, roll over the ink input ink this structure is characterized by correctly restrict each supply the location of the monlchamus region of adjustment on the nearby monlchamus area for inking, plastic affected by friction, easy-to-wear constantly, you need to change on a regular basis.

而电不静调度是用遥控安拆来举行的，凡是的不朱斗座底下拆有一排琴键式铁板，暗不天包围一张软塑料片，而塑料片具有不塑性，制止油不朱的渗漏，每块铁板的前端拆有一个公道辊，辊双方的支承环不兵塑料片底不松在不朱斗辊上，不朱斗座上共拆有30～32个公道辊，每个公道辊的宽度约为30～32mm，当伺服电机剥夺把持台的暗记后，堵住板滞布局，保持公道辊与不朱辊的间隙，因此当不朱斗辊不静弹时，不静员油不朱挤不抬塑料片，不梢据间隙巨细变成差别不朱层厚度，附着在不朱斗辊上，堵住传不朱辊不输出匀不朱机构，这栽布局的特不面是可以不差不天不拘每个不求不朱区的场所，制止一个不朱区的调度差附近不朱区不求不朱度爆发感化，塑料片受到不停摩擦，难磨损，需按期调换。

During this time, the strings will stretch and seat on bearing surfaces, the hundreds of pieces of felt and buckskin in the action will pack down causing a slight change in their dimensions which will affect the regulation.

在这个时间内，琴弦将继续发挥它的张力并作用于弦枕的表面。击弦机上几百片的呢毡和麂皮将会收缩变实，尺寸上会有一些轻微的变化，这样会影响到它的调整。

Metal cock ring soft seat surface pressure to the bearing surfaces, such as the valve core and valve seat is concentric ring surface can be a double tight closure.

金属旋塞表面压向阀座环软支座表面，如阀芯和阀座环表面是同心的，就能得到双重严密的关闭。

Took the different diameters double-row bearing slewing ring asexample, this dissertation studied the distribution of axial press ofthe rolling body under axial load and throw moment, the contact pressbetween two outer seat-rings which are connected to the main machinewith high strength screw bolts.

本文以双排异径球式回转支承为例，对球式回转支承在承受轴向载荷和倾翻力矩时的滚动体轴向正压力大小、分布及由高强度螺栓与主机连接的滚圈接触面的接触力进行了详细的理论推导和实际计算，说明在双排球式回转支承的结构静力分析过程中，可以将滚圈安装接触面的接触力简化为铅垂方向的均布载荷。

From the work force through the roller bearing shaft and bearing system, sent to the saddle or machine roller seat.

来自工作轧辊的力通过支承轴和支承鞍座系统传送到轧辊或机座。

The rider must also be placed centrally in the saddle seat to allow perfect balance, and free movement, and to maximise the bearing surface on the horse's back.

骑手还应该保证坐在马鞍的中心部位，这样才能保持最佳平衡状态，行动自如，同时最大限度地分担马背的压力。

To prevent overstressing the soil of a true abutment, the beam seat is sized so the centerline of bearing is at least 3 feet behind the MSE wall face and the bearing pressure on the reinforced soil is no more than 4 kips per square foot.

为了防止加筋土桥肩土体应力超限，梁座的尺寸要适当，以使得承载中心线离 MSE 墙面后至少3英尺，加筋土所受的支承压力不超过4千磅每平方英尺。

Press bearing cone on shaft, and seat bearing

压紧轴承，将轴承及护脂毡圈紧靠在卡环上。

Press bearing cone on shaft, and seat bearing

压紧圆锥形轴承内圈，将轴承及护脂毡圈紧靠在卡

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。