查询词典 be located in
- 与 be located in 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
A strong blue emission band between 350nm and 600nm was observed in the supported AAO templates unannealed. The central wavelength of the emission band was located at 435nm.
使用这些退火后的铝片,通过二次阳极氧化法制备的高度有序纳米阵列孔AAO膜为非晶态,并且在退火后转变为γ-Al〓O〓。
-
The pollution of nitrogen is rather significant in various regions in the whole country. The unattainment of mineralization and total hardness is mainly located in north-east, north China, north-west and south-west regions.
三氮污染在全国各地区均较突出,矿化度和总硬度超标主要分布在东北、华北、西北和西南等地区,铁和锰超标主要在东北和南方地区。
-
Fire mode selector was located in front of the triggerguard; separate safety was built into the cocking handle and was used to lock the bolt either in cocked or uncocked position.
消防模式选择是位于前面的扳机,单独的安全是内置在握把,结果被用来锁定竖起或uncocked的位置也螺栓。
-
Patagonia is located in a vast area below Buenos Aires and is famous for uncompromised beauty.
巴塔哥尼亚位于一大片下面布宜诺斯艾利斯是著名猛力美感。
-
Results indicate that radial distance of the bushing from the rotor center and the radius of the hemispherical bushing significantly affect wear rate,and minimzing both two values will result in lowest wear for micro-rotor systems in MEMS.However,it is noted that the bearing radius sets a lower limit on the hemispherical bushing radius since the bushings are located beyond the rotor inner radius.It is desirable to reduce their effects on friction and wear on micro-rotors by regulating the radius of the bushing and the radial distance of the bushing from the rotor center within permissive range of micro-fabrication.Severe wear exists with increasing applied load and rotating speed of the rotor.Stress distributions in the contact region are different from Hertz solutions due to the convergence stresses apearing on the uncontinuous curvature line and the contact pressures display symmetrical parabola in the contact region.
结果表明:在MEMS微转子系统中,微转子轴衬偏心距离和转子轴衬半径影响线磨损率,以两者减至最小为较理想,但须注意设计中轴承半径的限制,并使轴衬偏心距离大于轴承内半径;在转子加工制造许可的范围内,可以通过调整转子轴衬的半径和偏心距离来减少摩擦磨损对微电机的影响,随着转子所承受载荷和转子旋转速度的增加,其磨损严重;接触区的应力分布不同于经典Hertz解,这是由于应力集中出现在不连续的曲率线上,且接触区的接触压力呈现轴对称抛物线状分布。
-
So bored, so decided to try this restaurant despite being located in an unconvenient place.
星期6,谂唔到lunch食咩好,友人提议去&神厨馆&一试
-
Inversion holes caused by the vertical electric field EV/ are located in the spacing of two neighboring nC-regions on the interface by the force from lateral electric field (EL/ and the compositive operation of Coulomb's forces with the ionized donors in the undepleted nC-regions. This effectively enhances the electric field of dielectric buried layer EI/ and increases breakdown voltage
纵向电场所形成的反型电荷将被来自横向电场的电场力和未耗尽n+区内高浓度电离施主杂质的库仑力综合作用下固定于界面两个n+之间,从而能有效的提高介质场,增强器件的击穿电压。
-
Through the keyboard located on the front panel it is possible to display the amplifier main measures and to set or modify the relevant thresholds and pre-settings underpower alarm, remote controls, monitoring point signals, etc.
通过位于前面板的键盘,显示放大器的主要的尺寸和设置或更改相关的开端和预设置是可能的(低压报警,遥控控制,监视要点信号,等等。
-
On the front panel there is a display where the main operating parameters can be visualized; through the keyboard located below the display some settings can be modified underpower alarm threshold, output power indication, remote control selection, etc.
在前面板有一个显示器,主操作参数可以直观显示;通过安置在显示器下面的主板,一些设置可以更改(低电压报警极限,输出电力指示,遥控控制选择,等等
-
B.ALL undimensioned features shall be located within a tolerance of .005 from datum zeroo.
所有未注的特征相对于基准零点的位置偏差须在0.005之内。
- 相关中文对照歌词
- Tată (Father - Romanian Version)
- Te-Am Visat
- La Fête Des Mères
- Tu Şi Eu
- Non Coupable
- Disque D'or
- În Culori
- Inside My Head
- On Fait L'taf
- Boig Per Tu
- 推荐网络例句
-
The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.
论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。
-
I have not really liked him,I do not like his this kind of disposition.
我没有真的喜欢他,我不喜欢他的这种性格。
-
As we know the price of traditional product is composed of the cost and the profit of the company involving market competition, monopolizes and many other factors.
我们知道作为传统的商品,定价的模式往往是在成本的基础上增加厂商的预计利润而形成其价格,当然也要考虑到市场竞争、垄断等其他方面的因素。