查询词典 be in line for

Firstly, according to this character, primacy central point is detected by the exploring extremum method in the windows of 3×3 pixels. Then, basing on this central point, approximate normal line at ±45°、0°and 90°angle are drew.if the minimums of normal line is at central point and the difference between the minimums and the maximum in the normal line is more than the threshold, this point is considered to the edge point of image.

首先，在3×3象素的窗口中，如果中心值为最小值，则以该点为基础，以±45°、0°和90°方向作为近似法线带，然后判断该法线上的象素最小值是否在切点上（即是否在法线的中心点上），再通过检验切点与轮廓法线上亮度极大值的差值是否超过阈值，来判断切点是否为边缘轮廓上的点。

Provides for the pitch d, f, a, c, and f-line painted red, c painted yellow line (later to become Zhonggao Yin Staff and the origin of the bass clef). The 13th century was the first use of 5 lines, to become the predecessor of Staff. 16th century and increase the line to make the pitch more complete records.

规定音高为d、f、a、c，并将f线画成红色，c线画成黄色（后成为五线谱中高音及低音谱号的起源）。13世纪有人使用第5根线，成为五线谱的前身。16世纪又有加线的办法，使音高的记载更完备。

The company owns the industry's most advanced product release suspended production line, set the beat automatically Tooling flip board production line equipment, such as five lines, at the same time, Germany also has a Wagner paint line; has advanced gas detection chamber, electrical testing room, equipped with advanced detection measurement, laboratory equipment, and rely on high-tech talent, to create a more technology-gas products, are sold in every region of the world.

公司拥有目前行业内最先进的悬挂式积放生产线、定节拍自动翻转工装板生产线等5条装备流水线，同时还配有德国瓦格纳喷涂线一条；拥有先进的燃气检测室、电器检测室，配备先进的检测测量、实验设备，并依托高科技人才，创造出更高技术的燃气产品，销售到全球每个地区。

The yield strength of the line pipe is the key factor for strength design of pipelines, but the deviation of the test result of yield strength by the most universal normative round bar specimen and flattened strip specimen cannot be ignored in high strength line pipes, which does give more bewilderedness to the inspection and evaluation of line pipe.

管线钢管的屈服强度是管线强度设计的基本参数，但是最常用的标准圆棒试样和板状试样测试钢管横向屈服强度的结果存在明显差异，并且差异随钢级的提高而增大，给实际的生产检验和评价带来困惑。

From 1 to 8, this one is the main line; 4/16/34 is the main line of the first bifurcation point; 5/11/15 is the last main line of a bifurcation point; turn bar and so on.

从1到8，这一条就是主线；4/16/34是主线上第一个分叉点；5/11/15是主线上最后一个分叉点；依次类推吧。

Our process capability: Plates: FR4, High TG FR4, high CTI FR4, high frequency materials, halogen-free materials, aluminum and other low-rise Materials :2-20 layer of finished copper thickness :0.5-5 OZ finished thickness: 0.2 -6.0mm Minimum line width: 3mil Minimum line spacing: 3mil smallest shape tolerances:+/-0.1mm minimum finished diameter: 0.1mm maximum thickness aperture ratio: 12:1 wide minimum solder bridge: 4mil characters minimum line width: 5mil Minimum height of characters: 30mil Solder Mask Color: Green, black, blue, white, yellow, purple characters such as color: white, yellow, black and other surface processes: spray tin, lead-free HASL, Electroless gold plating Shuijin, OSP, chemical Shen tin, silver and other chemicals Shen Process: Goldfinger, blue gum, Blind-via/Buried-via, characteristic impedance control, rigid-flexible combination of reliability testing such as: Open / Short testing, impedance testing, solderability testing, thermal shock testing, metallographic analysis of micro-slice curvature Isoptera: 0.7% flame retardant Level: 94V-0

我们公司的制程能力：板材：FR4、高TG FR4、高CTI FR4、高频材料、无卤素材料、铝基材料等层数：2-20层成品铜厚：0.5-5 OZ成品板厚：0.2-6.0mm最小线宽：3mil最小线间距：3mil最小外形公差：+/-0.1mm最小成品孔径：0.1mm最大板厚孔径比：12：1最小阻焊桥宽：4mil最小字符线宽：5mil最小字符高度：30mil阻焊颜色：绿色、黑色、蓝色、白色、黄色、紫色等字符颜色：白色、黄色、黑色等表面工艺：喷锡，无铅喷锡、化学沉金、电镀水金、OSP、化学沉锡、化学沉银等其它工艺：金手指、蓝胶、盲埋孔、特性阻抗控制、刚柔结合等可靠性测试：开/短路测试、阻抗测试、可焊性测试、热冲击测试、金相微切片分析等翅曲度：≤0.7%阻燃等级：94V-0

According to the original plan to plant gum ebastine oncontour des cription, yin to write off a bit of the solid line that the leucogranites part of the dashed line just like the Internet image dot propomon descend to steam-and-ink, the line displayed is referred to as "blue mold" in translucent Lithographing of adhesive tape, then to bandnoise and extracranium needle stroke, put on, and then charged with paste paper will be charged against print-out, transfer to a long fibers'interface scourability yarn of paper, to sweep the LAN Dian powder, and will be responsible for the falling rocks, flushed with water, it emerged, each color will have to follow the program falls, injuring a writing brush and steam riemerella Tsui pen-and-ink hand according to the profile, the tone of a dense gradient is vvibdv Tsui pen point network.

照原图以植物胶依边框勾描，晴位部以不实线表现，浅色局部以实线不离像上钩图像的深浅网不面比例，以汽火不朱不兵线条表现不入来，称为「蓝模」，刻画在半透明的石印胶纸上，再以针笔勾瘪纹，擦上黑不朱，再用浆糊纸不兵黑不朱不正印不入来，转印于一种不幼纤维的冲纱纸上，以蓝靛粉扫上，再不兵之功降石上，以火冲刷，边框便呈现不入来，每一个印色便给依步调降一块石，再以羊毫及鸭咀笔用汽火不朱依边框手描，浓不浓不突变色调则给用幼咀钢笔不面网。

The paper introduces the concept of curve following turnout branch line and some relevant regulations,discussing maintenance method of mini-typed curve on railway with coordinate method based on original curve following turnout branch line at Rolling Line No.

介绍道岔附带曲线概念及其有关规定，结合中3条原有附带曲线的特点，阐述用坐标法对铁路线路上小型曲线的维修方法。

From the burden increased aspect clarify set up the necessity of station, then pass to drew up to set up generalize of transformer substation and line direction to consider, and pass to analysis of carry the data, safety, economic and dependable consider and made sure the 110 kV, 35 kV, 10 kV and station use electricity of lord connect line, then again through burden calculation and power supply scope made sure main number, capacity and model number of the transformer set, also in the meantime make sure the station uses capacity and model number of transformer, end, according to biggest keep on work electric current and short circuit calculating of calculation result, to the high pressure Rong break a machine, insulate a switch, female line, insulate son and wear a wall set tube, electric voltage with each other feeling machine, electric current with each other the feeling machine carried on choose a type, thus completed a 110 kV electricity a part of design.

本文首先根据任务书上所给系统与线路及所有负荷的参数，分析负荷发展趋势。从负荷增长方面阐明了建站的必要性，然后通过对拟建变电站的概括以及出线方向来考虑，并通过对负荷资料的分析，安全，经济及可靠性方面考虑，确定了110kV ，35kV ，10kV 以及站用电的主接线，然后又通过负荷计算及供电范围确定了主变压器台数，容量及型号，同时也确定了站用变压器的容量及型号，最后，根据最大持续工作电流及短路计算的计算结果，对高压熔断器，隔离开关，母线，绝缘子和穿墙套管，电压互感器，电流互感器进行了选型，然后进行配电装置和平面布置的设计以及防雷的设计，从而完成了110kV 电气一次部分的设计。

The test results indicate that,because of the capacitive coupling between500kV high voltage line and400V power-supply line,high voltage was induced on the power-supply line during the isolator operation.

试验结果表明，开关操作时由于500kV串内连接线和400V电源线间存在电容耦合，在操作电源供电母线上有较高的感应电压存在。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。