查询词典 be cast up on

The cast extended from the dilated inferior cave vein into the right atrium, and the inferior cave vein, common iliac vein, internal iliac vein were also filled with free-floating cast. Four patients underwent surgery, and the pathological results were correlated with CDFT.

结果 7例患者超声图像均显示右心内随心动周期漂浮样运动的网格状或实质性的肿物回声，并与下腔静脉和／或骼静脉内的肿物回声相连，诊断为心内平滑肌瘤病。4例患者行手术治疗，病理结果与超声结果一致。

Distinguished from the Cu content which have the optimal effect on cast strength is 5% with the chill casting, the Cu content that have the optimum effect on cast is 8% in the squeeze casting, furthermore, its strength effect is much better. The vacancy consistency of casts is raised in the squeeze casting which makes speed the diffuse velocity of atom and heat treatment process.

比压还增加了铜在铝基体中的溶解度，和金属型铸造时铜对铸件的最大强化作用发生在含量为5%时不同，挤压铸造时铜对铸件强化最大的含量为8%，强化效果较金属型铸造时更佳。

The cast steel and high chromium cast iron were used respectively as handle and head of the hammer.

分别采用高铬铸铁和碳素钢作为锤端和锤柄。

Cr15Mo3 is chromium wear-resistant white cast iron, heat treatment of the microstructure of martensite matrix of chromium carbide + Paralympic +, macro-hardness of HRC 60 or more wear resistance than Ni-Hard Cast Iron It is a very good wear-resistant material that can be produced coal mill, ore crusher, cement mill, shot blasting machines, mud pump, slurry pumps and other wear and tear serious casting.

Cr15Mo3 是铬系耐磨白口铸铁，热处理后的金相组织为马氏体基体+铬的碳化物+残奥，宏观硬度HRC在60以上，耐磨性能优于镍硬铸铁，是非常好的耐磨材料，可制作磨煤机、矿石破碎机、水泥磨机、抛丸机、泥浆泵、渣浆泵等磨损严重的铸件。

You can start with the image of neutral grey zone for color cast judgement, and the region as the target tube do with gray scale of neutralized, that is, set the value with a neutral color cast of neutral grey area.

可以不后从图像的洋性灰地区怠工色偏鉴定，并以该地区为标的目的用滴管怠工同灰度级的洋性冻，即用洋性值撤销色偏的洋性灰地区。

This paper has reviewed and analyzed the development of China's iron cast technologies in cupola smelting, electric furnace smelting and various cast iron alloys, and forecast its prospects in future.

本文从冲天炉技术、电炉技术和铸铁合金等方面回顾和分析了我国铸铁铸造技术的发展，并论述了未来的发展方向。

At the same time, the company also has production JP low-voltage distribution cabinets, power station control cabinet and all kinds of distribution box, and is supporting the transformation of rural power equipment manufacturing plant, the company has a casting factory, with a large cupola furnace, Mixer, Shot casting machines and other equipment and testing equipment, capable of producing various grades of gray cast iron, wear-resistant cast iron, ductile iron castings.

同时公司还具备生产JP低压配电柜，电站控制柜及各种配电箱的能力，是农村电网改造配套设备的生产厂，公司设有铸造分厂，具有大型化铁炉，混砂机，喷丸机等铸造设备和检测设备，能生产各种牌号的灰口铸铁、耐磨铸铁、球墨铸铁铸件。

By means of high speed gas stream compound with coaxial cutting gas for pulsed Nd:YAG laser on cutting of ceramics,the technological parameters affected on the thickness of re cast layer and the exiting of crack in re cast layer were studied.

针对激光切割陶瓷产生的重铸层和裂纹，设计了超音速喷嘴，采用侧吹高速辅助气流与同轴切割气流复合技术，研究了激光加工工艺参数对重铸层及裂纹的影响规律，开发了获得最小重铸层厚度和裂纹长度的高效率激光切割方

Key products include: cast iron plate, cast iron platform, the test platform, crossed platform, Maohan platform, fitter platform, table, Ping-foot, to me, V-type, V-iron, right-angle-foot, V-iron, foot bridge , Curved panels, machine damping Sizing Block, adjusted Sizing Block, partial-place, Jack, special wrench, gear Gear beat Tester; platform granite, marble slab, Ping-foot, V-iron, to me, Jiaochi, V-shaped blocks, such as platform support.

主要产品包括：铸铁平板、铸铁平台、检验平台、划线平台、铆焊平台、钳工平台、工作台、平尺、方箱、V型架、V 型铁、直角尺、V型铁、桥尺、弯板、机床减震垫铁、调整垫铁、偏摆仪、千斤顶、特种扳手、齿轮齿圈跳动检查仪；花岗石平台、大理石平板、平尺、V型铁、方箱、角尺、V型块、平台支架等。

Finally, several sets of cast dies and molds, including V6 transfer mold emplyed by GM, shoe die and piston die used for Santana, have been casted by LS high precise die-making system. All of these dies only needed a little machinaity. The cost and manufacture period of cast dies are lower than those of traditional wrought dies.

最后，采用LS法精密模具制造技术，用铸铁和新开发的铸造模具钢MCH13钢浇铸了多副模具，如V6发动机曲轴模、鞋模、桑塔纳轿车用活塞模具等，这些模具仅需进行少量的机加工即可进行使用，其生产成本及制作周期大大低于同类传统方法制造的模具。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。